Wagner Project 115 - 0418A - Safety Information
When working outdoors:
Vapors containing solvents may not be allowed to
blow toward the unit.
Note the direction of the wind.
Danger
Set the unit up in such a way that vapors containing
solvents do not reach the unit and build up there.
A minimum distance of 5 m between the unit and
spray gun is to be maintained.
Cleaning the unit
U
Danger of short circuit through penetrating water!
Never spray down the unit with high-pressure or
high-pressure steam cleaners.
Danger
Components and Description
The shipping carton for your painting system contains the following:
• Spray gun with two filters (M in gun and one XS-S and one M separate)
• Two wheel assemblies (including 2 metal covers and 2 plastic covers)
• 7.5 m, 1/4" internal diameter pressure hose
• An assembly aid (positioned beneath the hopper)
Figure 1 - Controls and Functions
(further, detailed descriptions of the individual items can be found in the relevant section of the operating
instructions)
Item
Component
A)
Extendable handle .......................The handle extends for easy transport and storage.
B)
Removable Hopper ......................The hopper can be removed for easy emptying and cleaning. It can be removed when empty or
C)
ON / OFF Switch ............................The ON/OFF switch turns the power to the sprayer on and off (O=OFF, l=ON).
D)
PRIME / SPRAY Knob ....................The PRIME/SPRAY knob directs fluid to the spray hose when set to SPRAY or the return tube when set
E)
Project Control ...............................Project Control functions: Prime, Clean/Roll, Spray 1 - MAX Spray.
F)
Return Tube ....................................Fluid is sent back out through the return tube to the original container when PRIME/SPRAY knob is in
G)
Handle lock .....................................The handle lock allows the extendable handle to extend or contract.
H)
Spray Gun ........................................For application of the coating material and regulation of the pump capacity.
I)
Spray Hose ......................................The spray hose connects the gun to the pump.
Technical Data
Pump type
Power source
Power consumption
Fusing
Double insulation
Max. spray pressure
1)
Max. delivery rate
Sound pressure level
2)
Sound pressure output
2)
2)
Oscillation level
Max. temperature of coating
substance
Max. nozzle size
Description
when filled with material. Do not exceed 9.5 liters. The cover of the hopper does not seal, therefore
material can emerge from the upper container if too much material is put in or the hopper tips up.
to PRIME. The arrows on the PRIME/SPRAY knob shows the rotation directions for PRIME and SPRAY.
The PRIME/SPRAY knob is also used to relieve pressure built up in the spray hose (see Pressure Relief
Procedure).
PRIME position.
Piston pump
230-240 V
50 Hz
~
625 W
Only connect to sockets protected
with an FI fuse (16 A)
190 bar
0,8 l/min
L
= (80+3) dB (A)
WAd
L
= (91+3) db (A)
pAd
a
=1,2 m/s
h
Uncertainty K = 1.5 m/s²
48°C
L (0,017")
Cleaning units with solvents
U
When cleaning the unit with solvents, the solvent
should never be sprayed or pumped back into a
container with a small opening (bunghole). An
explosive gas/air mixture can be produced. The
Danger
container must be earthed.
Do not clean the device or accessories with
flammable solvents with a flash point below 21 °C.
Earthing of the object
U
The object to be coated must be earthed.
• One axle, two axle plates and four screws
• Spray tip assembly
• One inlet valve pusher tool
• Instruction manual
Hose length
Container capacity
Product dimensions
Weight
1)
Dispersion paint with nozzle M and a pressure of 138 bar
2
Measured in accordance with EN 1953 in an acoustic measuring
)
room with paint sprayed at maximum pressure
Coating Materials Suitable for Use
Water-based and solvent-containing lacquers and glazes.
Paints, oils, release agents, synthetic enamels, PVC lacquers,
undercoats, base coats, fillers and anti-rust paints.
Dispersion and latex paints for interior use.
15
Technical Data
7,5 m
9,5 l
38 x 38 x 65 cm
12 kg