Klauke Multi Mode D'emploi page 11

Instruction Manual EK 60 UNV
______________________________________________________________________________________________________________________
Do not leave or operate the charging unit in rain or snow. Do not
charge the battery near lightly inflammable materials or gases.
Do not use the cord to transport the charging unit or to pull the plug out
of a wall socket with force. Do not insert strange parts into the ducts of
the charging unit.
The charging of the batteries must only be done with charging units
supplied by the manufacturer.
Attention
Do not place the battery in your pocket or in your
toolbox if there are any conductive materials in it such
as coins, keys, tools or other metallic parts.
Pull the plug of the charging unit after charging. Do not disassemble
the charging unit or battery.
In order to safeguard a safe and proper performance of the charging
unit the repair and service of the unit should be made through our
Service Center.
5.6 Storage and transport of the crimping tool
In order to protect the tool against damages it has to be cleaned
carefully after each use and be put into the transportation case which
has to be closed safely.
6. Troubleshooting
a.) Flashing of the light diode display (Pos.-No. 6)
=> See chapter 4.3 for more information about the special functions
of the tool.
b.) The tool loses oil.
=> Return the tool to the manufacturer. Do not open the tool and
damage the seals of the tool.
c.) The crimping tool does not reach the final operating pressure.
=> Stop the crimping process. Press the retract button (Pos.-No. 2)
and the operating switch continuously and simultaneously for about
10 sec. Is the malfunction not be eliminated by this attempt the tool
has to be returned to the manufacturer.
7. Putting out of operation/waste disposal
The disposal of the various components of the tool has to be treated
separately. First you have to dispose of the oil at special delivery
points.
Attention
Hydraulic oils represent a danger for the ground-water.
Uncontrolled draining of or improper disposal is under
penalty. (environmental liability law)
Next, the battery cartridge (Pos.-No. 7) has to be specially disposed of
according to the EEC Battery Guideline.
For the disposal of the remaining parts please reference the EC
environmental guideline.
Because of possible environmental damages we recommend to dispose
of the tool by professional companies.
Attention
Do not dispose of the unit in your residential waste
because it will finally end up on the waste dump which
would be hazardous for the environment.
A return of the old tool free of charge to the manufacturer cannot be
granted.
8. Technical Data
Weight of the complete tool:
Crimping force:
Battery voltage:
Battery capacity
Charging time:
Crimping time:
Crimps per battery:
Max. cutting diameter:
Cutting time:
Cuts per battery:
Punching time:
Capacity:
Hydraulic oil:
Environmental temperature:
Sound level:
Vibrations:
Dimensions:
Note
Additional instruction manuals are available free of charge. The part # is
HE.7569_H.
page 11
approx. 4,5 kg (incl. battery)
approx. 60 kN
12 V
3 Ah (RA5)
approx. 1 h (LG4F),
¼ h with Quickcharger (LG5)
approx. 5 s to 8 s
(depending on the connector size)
approx. 125 crimps
(Cu 150 mm² DIN 46235)
40 mm ∅
8 s to 20 s
(depending on the cable size)
approx. 75 cuts (4x70 mm² NYY)
5 s with 22,5 mm ∅, 3 mm St37
12 s with 60 mm ∅, 3 mm St37
• 60 cycles per battery
with 60 mm ∅ in 3 mm mild steel
• 170 cycles per battery
with 22,5 mm ∅ in 3 mm mild steel
approx. 150 ml "Shell Tellus T 15"
-20°C to +40°C
70 dB (A) in 1m distance
< 2,5 m/s²
See Picture 7