Selecting/Starting A Program - bredent thermopress 400 Manuel D'utilisation Et D'entretien

7.1 Selecting - starting a program
(Start menu, CE level)
01: Set main switch (01) to On.
02: Select program; if necessary use yellow keys (11/12) to select in
Menu
the main menu.
Menu
03: Confirm by pressing Enter (16) once.
Enter
04: Use the yellow keys (11/12) to select the respective program.
Menu
Menu
05: Confirm by pressing Enter (16) once.
Enter
06: Start program with Start heating (03) key.
07: Deactivate buzzer with key (10).
08: Insert cartridge and slide in according to chamber lever position 1 / 2.
Lubricant must be added!
Note: Adhere to the instructions for use of the thermopress resins!
09: Start heating time key 1 (05) or
Start heating time key 2 (07) or activate both within
approx. 5 minutes according to the selected chamber.
10: At the end of the heating time deactivate buzzer with key (10).
11: Insert flask into the flask chamber (22) and fix with the
clamping screws (18/19).
When fixing the flask with the clamping screw 1 (18), slightly press against the wall of the unit and then use the clamping screw 2 (19) to clamp the flask against
the heating cylinder (23). The flask should not move the heating cylinder (23) when it is fixed in order not to block the injection process. (error message shown on
the display) If required, the position of the heating cylinder lever (17) must be adjusted.
Attention: Do not insert the flask into the clamping device too early since the metal flask absorbs too much heat from the heating cylinder. This will affect the
melting hehavior of the resins. The granular material is not melted and faulty injections may result.
12: Attention! The injection process can only be started, if the flask
chamber lid (24) (protective lid!) is closed.
Press Start injecting key (09).
13: Open the flask chamber lid (24) (protective lid!) after the injection
process; then loosen the clamping screws (18/19) and move the
bracket (20) upward.
14: Press Eject cartridge key (08). The piston will move backward.
Attention! Press the eject key only after the piston has
completely moved back after the injection process and is in idle
position.
Then remove the flask from the flask chamber (22).
15: A new injection process can be performed.
bredent GmbH & Co. KG · Weissenhorner Str. 2 · 89250 Senden · Germany · T: +49 7309 872-441 · F: +49 7309 872-444
www.bredent.com · @: info@bredent.com
Display and help
The company logo of bredent is displayed for approx. 7 sec (initalizing
phase); then the menu selection is displayed.
Select program
Program / No. 1-30 / name is displayed
The display changes to program name with set temperature (°C).
Display changes to Heating set and actual temperature. The buzzer is
heard when the set temperature is reached.
Program + Set reached
Insert K1 – K2
To ensure uniform melting of the resin, the cartridge must be
inserted 1 mm deeper (avoid flush insertion).
Heating time parameters
Program name HZ1: .. min
= ... °C HZ2: .. min
Program Inject1ready (protective lid!)
=...°C
Attention: When inserting the flask, the injection opening must face the
cartridge.
Time runs down on the display.
Program Inject1: ...s
HZ2: blank
Program Inject1ready
Eject K1?
The cartridge is pressed out of the heating cylinder. It is not required to
previously separate it from the flask. Excess material is pressed in the
empty flask chamber together with the flask.
EjectingK1
The temperature is kept until new start Heating time 1/2 (05/07) or
End CE (15) is selected.
19