SOLIS BARISTA PERFETTA PLUS 1170 Mode D'emploi page 71

ST ORI NG THE SOL IS B ARISTA P ERF ET T A PL U S
■
ESPR ES S O M ACHINE
Store the cooled down, cleaned and dry machine in an upright position, ideally in
the original packaging. Do not place any items on the appliance.
D E S CA L IN G
s
If your machine requires a descaling cycle, the machine will emit a descaling alarm:
GB In operation mode, the steam button flashes red and both coffee buttons constantly
light up white.
In this case, the machine can still be used, but none of the settings (except for the
coffee quantity) are available at this moment.
ATTENTION: In the event of an alarm, you should descale your machine immediately
in order to prevent the functionality from being reduced or the coffee quality from
degrading. Repairs to the espresso machine relative to limescale problems are not
covered by the warranty if the descaling procedure described below is not performed
regularly.
Solis recommends descaling your Solis Barista Perfetta Plus espresso machine with a
mixture of SOLIPOL® special and water. Please use only SOLIPOL
703.02) for descaling the machine. Damages caused by the use of improper desca-
ling agent are not covered by warranty.
When the descaling alarm is displayed, please proceed as follows:
1. Remove the water tank from the appliance and empty it out. Remove the
BRITA water filter from the tank. Fill the water tank with 0,5 litres of water and
®
0,5 litres of SOLIPOL special so that the tank is filled with 1 litre of descaling
solution. Place the water tank back on the rear of the appliance. Empty the drip
tray and reinsert drip tray and grid.
2. Place a large container under the brewing head and place the empty milk jug
under the steam/hot water wand.
3. While the descaling alarm is displayed, press the Prog. button, now the Prog.
button and the steam button flash red.
4. Now, press the steam button to start the automatic descaling program. The
Prog. button and the steam button flash quickly. The descaling program lasts
less than 15 minutes with few cycles. During one of these cycles, turn on the
steam/hot water control (M) to allow steam to escape so that the steam wand
is also descaled. Then, turn the control back to the OFF position. During the
pauses, the tank can be emptied, making it possible for the tank to hold less
than 1 litre to make sure that the tank can stand on the drip grid. Drip tray and
grid must not be removed.
5. After these cycles, the descaling process ends, a double signal sounds, the Prog.
button and the steam button flash more slowly again. Now the machine has to
be rinsed to remove the descaling residues.
140
6. Refill the water tank with minimum 1.2 litres of tap water. Empty both contain-
7. Press the steam button, approx. 1 litre of water will run through the brewing
8. When the rinsing process is complete, both coffee buttons light up white again,
9. Remove the water tank again, empty it out, rinse it with clear water and reinsert
NOTE: Please wipe potential splashes of descaling solution on the appliance casing
away immediately, as the agent might damage the surface.
NOTE: If the descaling procedure is not completed correctly (e.g. no electricity), we
recommend to complete the procedure and rinse properly the appliance.
WARNING: Never submerge power cord, power plug or the appliance itself
®
special (Art.-No. in water or any other liquid. During descaling, never remove the water tank
or allow it to empty completely.
s
ATTENTION! In general: If a button flashes red, it represents an alarm signal!
NOTE: The appliance remains operational and coffee can still be dispensed. Only the
settings are unavailable while an alarm is emitted.
WAT ER FIL T ER HA S TO BE REPLA CED :
■
For the water filter alarm, the
and red, the
Once the water filter alarm is emitted, please proceed as follows:
1. Press the Prog. button.
2. Remove the water tank, remove the water filter, rinse the water tank and insert
a new filter. Fill the tank with cold water up to the Max-marking and reinstall the
water tank. Please refer to page 124 –125 for information on how to install the
BRITA INTENZA water filter.
3. Place the container under the brewing group.
4. Press the
through the appliance.
5. Once the
operation mode.
ers and the drip tray. Replace the drip tray and grid. Place the two containers
back under the brewing head resp. under the steam/hot water wand.
group without a pause. During this rinsing process, open the steam/hot water
control once to the maximum position for minimum 20 seconds so that the
steam/hot water wand is also rinsed. Then, turn the steam/hot water control
back to the OFF position so that the remaining water runs through the brewing
group. During the rinsing process, the Prog. button and the steam button flash
quickly again.
the other buttons are not lit up and a signal sounds twice.
the water filter. Empty the drip tray and rinse it.
T H E A L A R M SI G N A L S
BUTT O N F LA SHES WHI TE / RE D
button alternately flashes white
button lights up white.
button to activate the automatic rinse cycle. 500 ml of water are fed
and buttons constantly light up white, the appliance is back in
GB
141