Remote Control Led Flashing Code And Acoustic Signal; Replacing Remote Control Batteries; Uncoupling The Towing Vehicle; Manoeuvring The Caravan - Truma Mover XT4 Mode D'emploi

Remote control LED flashing code and
acoustic signal
LED 1 red Displays the charging status of the caravan
battery
good LED off
weak LED lights up
flat LED on and LED 3 indicates a fault
LED 2 yellow lights up in the event of a temporary malfunc-
tion, and an acoustic signal is also emitted in
the event of overcurrent / overtemperature. The
power is automatically reduced. Allow the sys-
tem to cool down.
flashes when the Mover is engaged and the
control unit or remote control is switched off.
An acoustic signal is also emitted.
flashes during engaging / disengaging
flashes when switched on if the engaging / dis-
engaging process was not completed before it
was switched off last time. An acoustic signal is
also emitted. Restart and complete the engag-
ing / disengaging process. Only then can drive
commands be executed with the control knob
or slide control.
LED 3 red lights up in the event of a persistent fault, and
an acoustic signal is also emitted, e.g. in the
event of a faulty drive motor, engage the park-
ing brake. See "Troubleshooting"
Green LED 4 flashes slowly until the radio connection is estab-
lished when the remote control is switched on.
flashes four times with an acoustic signal if the
connection to the control unit is not established
within 10 seconds after the remote control is
switched on. The remote control then switches
off.
lights up when the remote control is ready for
operation and the data link is stable
flashes four times when the drive rollers are
disengaged and the control unit is switched off.
Then the remote control switches itself off.
flashes four times with an acoustic signal if no
button is pressed on the remote control within
3 minutes. The remote control then switches off.
flashes four times with an acoustic signal if the
radio connection is interrupted. The remote con-
trol then switches off.
All LEDs "off" and no acoustic signal
System off (check batteries in remote control if necessary)

Replacing remote control batteries

Use only leak-proof micro-batteries with a steel outer casing,
LR 03, AAA, AM 4, MN 2400 (1.5 V).
When inserting new batteries, take care not to reverse the
positive and negative terminals.
Figure 2
Flat, used batteries can leak and damage the remote
control. Remove the batteries if the remote control is
not being used for a long period of time.
No warranty is given for damage caused by leaking
batteries.
Disposal
Neither the remote control nor the batteries may be
disposed of with domestic refuse, instead they must be
sent for recycling separately via a collection point. By
doing this you are contributing towards reuse and recycling.

Uncoupling the towing vehicle

Secure the towing vehicle against rolling in accordance with
the vehicle instructions.
Secure the caravan against rolling. Engage the parking
brake and / or secure against rolling with wedges.
Before uncoupling, make sure that there is no tension
on the overrun brake.
Uncouple the caravan from the towing vehicle as usual. Un-
plug the 13-pole plug / adapter from the vehicle, undo the
breakaway cable, open the drawbar coupling and raise it with
the jockey wheel.

Manoeuvring the caravan

Before using the Mover XT4, read the "Safety
instructions".
When the caravan is uncoupled, engage the parking brake to
stop it rolling.
Plug the 13-pole plug / adapter into the safety socket of the
caravan (after unplugging it from the vehicle).
For safety reasons, the Mover XT4 can be operated only
when the 13-pole plug / adapter of the caravan is
plugged into the safety socket.
If the 13-pole plug / adapter is removed from the safety
socket, the Mover XT4 immediately stops working.
Switch on the remote control – green LED 4 flashes until the
control unit is ready for operation. If the control unit is not
ready for operation, the remote control switches off after
about 10 seconds.
Press the two buttons (i) for engaging simultaneously, and
engaging will start after approx. 3 seconds (safety delay).
After each engagement process, check the position in-
dicator to make sure that the four drive rollers are com-
pletely engaged. If the rollers are not fully engaged, repeat the
process.
EN 15