Operating Instructions; Remote Control; Switching On The Remote Control - Truma Mover XT4 Mode D'emploi

Operating instructions

Remote control

Protect the remote control from moisture and direct
sunlight.
LED 1 2 3 4
b
h
i
Figure 1

Switching on the remote control

a = On / off slide switch (also the emergency stop switch)
No other remote control function must be active when
the remote control is switched on.
On (LED 4 lights up*)
Off (LED 4 goes off)
* LED 4 flashes for approx. 5 seconds after the remote con-
trol is switched on, until the system is ready for operation.
The following options are available for controlling the caravan:
b using the control knob only
c using the slide control only
b + c using the control knob and the slide control
The caravan symbol on the control knob indicates the current
direction of travel (of the caravan).
The slide control allows the caravan to be moved forwards
and backwards without jolting, with infinitely variable speed
control.
Slide control only
(Forwards, backwards and infinitely variable speed control)
– Slide control forward –> caravan moves forward (towards
the drawbar)
(both wheels rotate in forward direction)
– Slide control backward –> caravan moves backward (away
from the drawbar)
(both wheels rotate in reverse direction)
The further the slide control is moved from the zero position,
the faster the speed.
Only Mover XT4 control knob
The caravan drawbar can be rotated to the right / left within
a range of approx. 30 cm using the control knob. When the
limit of the rotating range is reached, the rotating procedure is
stopped automatically.
It is not possible to turn a caravan with a two-axle chassis on
the spot. To continue rotating, the caravan must be moved
forwards or backwards in a straight line for a certain distance
using the slide control.
14 EN
Control knob and slide control, Mover XT4
(Cornering forward or backward to the right or left)
Operating the control knob and the slide control makes the
Mover XT4 go round in a circle, whereby the wheels rotate
continuously but the inner wheels rotate more slowly than the
outer wheels. Due to the design, it is not possible to manoeu-
vre in very tight bends with a two-axle chassis.
– Control knob to the right and slide control forward –>
caravan moves forward in the direction of the drawbar in a
right-hand bend
– Control knob to the left and slide control forward –>
caravan moves forward in the direction of the drawbar in a
left-hand bend
a
– Control knob to the right and slide control backward –>
caravan moves backward in the opposite direction to the
drawbar in a right-hand bend
c
– Control knob to the left and slide control backward –>
h
caravan moves backward in the opposite direction to the
drawbar in a left-hand bend
i
The more the slide control is pushed towards the end stop,
the faster the movement.
The more the control knob is turned, the smaller the turning
radius. The caravan can be manoeuvred accurately by using
the slide control and control knob at the same time.
Engaging and disengaging
The drive rollers are engaged and disengaged on the caravan
wheels by means of the remote control.
h = Two-handed operation disengagement of drive rollers
(drive rollers swing away from tyres)
i = Two-handed operation engagement of drive rollers
(drive rollers swing towards tyres)
against rolling with wedges.
To engage / disengage the drive rollers, always press both
buttons simultaneously – for about 3 seconds (safety delay)
– until you hear an acoustic signal and the drive rollers start to
engage / disengage.
During engagement / disengagement, the LED2 flashes and
you can release the buttons. When the drive rollers reach their
end position, you will hear a double acoustic signal.
pletely engaged or disengaged. If the engagement / disen-
gagement process is interrupted, it has to be restarted and
completed before more drive commands can be executed.
rollers are disengaged and automatically move to their end
position.
The remote control switches itself off automatically after ap-
prox. 3 minutes if none of the buttons are pressed. The green
LED 4 goes out.
To reactivate the remote control, move the slide switch
to "Off" and then back to "On"
2 seconds.
There is no "On / Off" switch on the caravan itself.
The side slide switch on the remote control (On / Off) also acts
as an "Emergency Stop switch". In case of noticeable prob-
lems, such as uncontrolled behaviour of the manoeuvring sys-
tem, immediately switch the slide switch on the side to "Off".
mote control is switched off and on again quickly, it remains
switched off.
Before disengaging, make sure that the caravan can-
not roll away. Engage the parking brake and / or secure
The drive commands with the control knob and slide
control are executed only when the drive rollers are com-
If the two buttons for disengaging are pressed while the
rollers are engaging, engaging is interrupted, the drive
The remote control can be switched on again only if it
has been switched off for at least 2 seconds. If the re-
after approximately