Fluval NANO Mode D'emploi page 2

IMPORTANT SAFETY INSTRUCTIONS
EN
WARNING – To guard against injury, basic safety precautions should be
observed, including the following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
1.
and all the important notices on the appliance before using. Failure to do so
may result in loss of fish life and/or damage to this appliance.
2. DANGER – To avoid possible electric shock, special care should be taken
since water is employed in the use of aquarium equipment. For each of the
following situations, do not attempt repairs yourself; return the appliance to
an authorized service facility for service or discard the appliance.
A. If the appliance shows any sign of abnormal water leakage, immediately
unplug it from thepower source.
B. Carefully examine the appliance after installation. It should not be plugged
in if there is water on parts not intended to be wet. If the appliance or any
part of it falls into the water DO NOT reach for it. First unplug the unit
before retrieving.
C. Do not operate any appliance if it has a damaged cord or plug, or if it is
malfunctioning or it is dropped or damaged in any manner. The power cord
of this appliance cannot be replaced; if the cord is damaged, the appliance
should be discarded. Never cut the cord.
D. To avoid the possibility of the
appliance plug or receptacle
getting wet, position
appliance to one side of a wall
mounted receptacle to prevent
water from dripping onto the
receptacle or plug. A "drip
loop" (see illustration) should
be arranged by the user for the
cord connecting appliance to
a receptacle. "The drip loop"
is that part of the cord below
the level of the receptacle or
the connector if an extension
cord is used, to prevent water
travelling along the cord and coming in contact with the receptacle. If the
plug or receptacle does get wet, DO NOT unplug the cord. Disconnect the
fuse or circuit breaker that supplies power to the appliance. Then unplug
and examine for presence of water in receptacle.
3. This appliance is not intended for use by persons (including children) with
significantly impaired physical or mental capabilities, unless they have been
given supervision or instruction concerning the use of the appliance by a
person responsible for their safety. Children should always be supervised to
ensure that they do not play with the appliance.
4. To avoid injury, do not touch moving parts or hot parts.
5. CAUTION - Always unplug or disconnect all appliances in the aquarium
from electricity supply before placing hands in water, before putting on or
taking off parts and while the equipment is being installed, maintained or
handled. Never yank cord to pull plug from outlet. Grasp the plug and pull to
disconnect. Always unplug an appliance from an outlet when not in use.
6. Do not install or store the appliance where it will be exposed to weather or
temperatures below freezing. FOR INDOOR HOUSEHOLD USE ONLY. DO NOT
IMMERSE.
7. Make sure the appliance is mounted correctly and securely positioned on
the aquarium before operating the appliance.
8. If an extension cord is necessary, a cord with proper rating should be used. A
cord rated for less amperes or watts than the appliance rating may overheat.
Care should be taken to arrange the cord so that it will not be tripped over
or pulled. The connection should be carried out by a qualified electrical
installer.
9. The socket-outlet shall be installed near the equipment and shall be easily
accessible.
SAVE THESE INSTRUCTIONS
For the complete use and understanding of this product it is recommended that
this manual is thoroughly read and understood. Failure to do so may result in
damage to this product.
Congratulations on your purchase of the Fluval Nano LED Lamp. Engineered in Germany, this lamp features
new C.O.B. (Chip-on-Board) technology, which allows multiple mini LEDs to be packed into a tighter, smaller
space. The result: higher energy efficiency, and a greater light output sustainable for over a longer period of time.
INSTALLATION AND USAGE:
LAMP & TAPE MOUNTING BRACKET INSTRUCTIONS
Surface Preparation
Surface temperature for application should be no lower than 60°F degrees (16°C) and not higher than 85°F degrees
(29°C). If climate will not permit, move unit to appropriate conditions. Area to receive tape should first be thoroughly
cleaned with a liquid detergent and warm water solution. Rinse with clea nwater and dry completely. A final wipe with
50/50 alcohol/water is highly recommended for best results (use a clean, lint-free cloth). Ensure surface is dry and
residue free before proceeding.
Note: The position of the mounting bracket cannot be changed after it has been affixed. Do not place the mounting
bracket over the back wall paper. It must be applied directly onto the aquarium glass.
the
INSTALL LIGHT AFTER 24 HOURS TO ALLOW THE TAPE BOND TO CURE PROPERLY
NOTE : FAILURE OF PROPER TAPE BONDING MAY BE ATTRIBUTED TO ONE OF FOUR ISSUES:
1. Poor surface preparation and/or application.
2. Poor adhesive contact: exposed adhesive side of tape being touched or contaminated.
3. Insufficient pressure being applied.
4. Lamp hung too soon, tape not fully cured.
FOR AQUARIUMS WITH TOP FRAMES.
1. Remove the protective film from the lamp mounting bracket. Affix the mounting bracket to the
outside of the tank indesired location; aligning the rim of the mounting bracket with the tank
frame and press firmly applying pressure while gently twisting to ensure proper adhesion.
CLEAN
FOR AQUARIUMS WITHOUT TOP FRAMES.
aquarium glass; affix the acrylic insert to the lamp mounting bracket before installing lamp mounting bracket.
1. Remove the protective film from the acrylic insert, and affix the insert to the lamp mounting
bracket.
2. Remove the protective film from the lamp mounting bracket. Affix the mounting bracket to the
outside of the tank indesired location; aligning the rim of the mounting bracket with the tank rim
and press firmly applying pressure while gently twisting to ensure proper adhesion.
CLEAN
Assemble the lamp to the lamp support. Slide the lamp support into the mounting bracket; and insert the height
locking clamp into the mounting bracket to assure that the lamp remains at desired height.
BASIC TROUBLE-SHOOTING:
If the fixture does not work, ensure that all plugs and wires are firmly connected, ie: connection from fixture to
transformer,and connection from transformer to electrical outlet.
MAINTENANCE:
Before any kind of maintenance, always disconnect electrical supply of the light fixture. For maximum LED performance,
it is recommended that the fixture and the LED lens be cleaned on a weekly basis. Unplug transformer prior to cleaning
the light fixture and remove from aquarium. Use both hands when manipulating this appliance. Wipe exposed surfaces
carefully with a damp cloth to remove any dust or mineral deposits that may collect over time. Do not use detergents
or harsh cleaners as it can damage the light fixture. Use Fluval LED Lens Cleaning Non-Aerosol Spray (A3969) to clean
the LED portion of the light fixture. Make sure all surfaces are dry before re-connecting the transformer to the power
source.
WARRANTY
3 YEAR LIMITED WARRANTY
The Fluval Nano LED Lamp is guaranteed against defects in material or workmanship under normal aquarium usage and
service for 3 years. We reserve the right to repair or replace at our option. Failure of less than 5% of the total number
of LEDS shall not be considered a defect under the terms of this warranty. This warranty does not apply to any light
fixture that has been subjected to misuse, negligence or tampering or commercial use. No liability is assumed with
respect to loss or damage to livestock or personal property irrespective of the cause thereof. This does not affect your
statutory rights.
FOR AUTHORIZED WARRANTY REPAIR SERVICE:
For Authorized Warranty Service please return (well packaged and by registered post) to the address below enclosing
dated receipt and reason for return. If you have any queries or comments about the operation of this product, please let
us try to help you before you return the product to your retailer. Most queries can be handled promptly with a phone call.
When you call (or write), please have all relevant information such as model number, age of product, details of aquarium
set-up, as well as the nature of the problem.
CANADA: Consumer Repair, Rolf C. Hagen Inc., 20500 Trans Canada Hwy, Baie d'Urfé, QC H9X 0A2
U.S.A.: Rolf C. Hagen (U.S.A.) Corp., 305 Forbes Blvd, Mansfield, MA. 02048
UK: Rolf C. Hagen (UK) Ltd, Customer Service Department California Drive, Whitwood Ind Est., Castleford West
Yorkshire WF10 5QH www.hagen-uk.custhelp.com
CALL US ON OUR TOLL-FREE NUMBER:
CANADA ONLY: 1-800-554-2436 between 9:00 a.m. and 4:30 p.m. Eastern Standard Time. Ask for Customer Service.
U.S. ONLY: 1-800-724-2436 between 9:00 a.m. and 4:00 p.m. Eastern Standard Time. Ask for Customer Service.
U.K. ONLY: Helpline Number 01977 556622. Between 9:00 AM and 5:00 PM, Monday to Friday (excluding Bank
Holidays).
RECYCLING: This symbol bears the selective sorting symbol for waste electrical and electronic equipment
(WEEE). This means that this product must be handled pursuant to European Directive 2002/96/EC in order to
be recycled or dismantled to minimize its impact on the environment. Check with your local Environmental
Agency for possible disposal instructions or take to an official council registered refuse collection point.
Electronic products not included in the selective sorting process are potentially dangerous for the
environment and human health due to the presence of hazardous substances.
Maximum frame height: 30 mm (1 1/8").
APPLY WAIT
To ensure lamp mounting bracket fits flush against the
APPLY WAIT