Table des Matières
Publicité
Equipement MIDI
ISystem Realtime Message
GTiming Clock
Status
F8H
* Received during creation of sync tracks in the Sync Track screen.
GStart
Status
FAH
* Received when creation of the sync track begins in the Sync Track screen.
GStop
Status
FCH
* Received when creation of the sync track is finished in the Sync Track screen.
GActive Sensing
Status
FEH
* When Active Sensing is received, the unit will begin monitoring the intervals of all fur-
ther messages. While monitoring, if the interval between messages exceeds approxima-
tely 400 ms, the same processing will be carried out as when Reset All Controllers is
received, and message interval monitoring will be halted.
ISystem Exclusive Message
Status
Data byte
F0H
iiH,ddH,......,eeH
F0H:
System Exclusive Message status
ii = ID number:
an ID number (manufacturer ID) to indicate the manufacturer whose
Exclusive message this is. Roland's manufacturer ID is 41H.
ID numbers 7EH and 7FH are extensions of the MIDI standard; Uni-
versal Non-realtime Messages (7EH) and Universal Realtime Messa-
ges (7FH).
dd,...,ee = data:
00H - 7FH (0 - 127)
F7H:
EOX (End Of Exclusive)
I Universal Non-realtime System Exclusive Messages
GIdentity Request Message
Status
Data byte
F0H
7EH,dev,06H,01H
Byte
Explanation
F0H
Exclusive status
7EH
ID number (Universal Non-realtime Message)
dev
Device ID (dev: 10H - 1FH, 7FH)
06H
Sub ID#1 (General Information)
01H
Sub ID#2 (Identity Request)
F7H
EOX (End Of Exclusive)
* Only a device ID of 7FH or message matching the BR-1200CD's device ID is received.
* When this message is received, Identity Reply message (p. 346) will be transmitted.
About Device ID
Exclusive messages are not assigned to any particular MIDI channel. Instead, they have
their own special control parameter called device ID. The Roland exclusive messages use
device IDs to specify various devices.
How to set the device ID:
1.
Press [UTILITY], move the cursor to [MIDI], then press [ENTER/YES].
The MIDI settings screen appears.
2.
Move the cursor to "Device ID," then rotate the TIME/VALUE dial to set the device
ID.
The Device ID can be set to any number from 17 to 32. It was set to 17 at the factory.
344
Status
F7H
Status
F7H
2. Data Transmission
IChannel Voice Messages
GNote off
Status
2nd byte
8nH
kkH
n = MIDI channel number:
kk = Note number:
vv = Note off velocity:
GNote on
Status
2nd byte
9nH
kkH
n = MIDI channel number:
kk = Note number:
vv = Note on velocity:
* Transmitted by drum pattern using the selected MIDI channel number when the MIDI
parameter "Drums Ch." is set to 1–16.
* Transmitted by bass pattern using the selected MIDI channel number when the MIDI
parameter "Bass Ch." is set to 1–16.
* Transmitted according to the content of the SMF during playback of SMFs.
* Notes sounded by the drum pattern correspond to note numbers as follows.
Rhythm Guide Tone
Note Number
Hi-Q
D#1 (27)
Stick
G 1 (31)
Metronome (click)
A 1 (33)
Metronome (bell)
A#1 (34)
Kick 2
B 1 (35)
Kick 1
C 2 (36)
Snare 1
D 2 (38)
Snare 2
E 2 (40)
Tom 1
F 2 (41)
Closed hi-hat
F#2 (42)
Tom 2
A 2 (45)
Open hi-hat
A#2 (46)
Tom 3
C3 (48)
Crash cymbal
C#3 (49)
Tom 4
D 3 (50)
Ride cymbal
D#3 (51)
Cow bell
G#3 (56)
Claves
D#5 (75)
GPolyphonic Key Pressure
Status
2nd byte
AnH
kkH
n = MIDI channel number:
kk = note number:
vv = Polyphonic Key Pressure:
* Transmitted according to the content of the SMF during playback of SMFs.
GControl Change
* Transmitted according to the content of the SMF during playback of SMFs.
❍Bank Select (Controller number 0, 32)
Status
2nd byte
BnH
00H
BnH
20H
n = MIDI channel number:
mm, ll = Bank number:
* When the MIDI parameter Effects P.C. is set to PC+BANK, this is transmitted via the
MIDI channel selected in the Effects Ch. setting when insert effects patches are switched.
* For the correspondence between Bank Select/Program numbers and the insert effect
patch banks/numbers, see p. 343.
❍Volume (Controller number 7)
Status
2nd byte
BnH
07H
n = MIDI channel number:
vv = Volume:
* When the MIDI parameter "MIDI Fader" is set to ON, this is transmitted via the MIDI
channel set for a track when the corresponding track fader is moved.
3rd byte
vvH
0H - FH (ch.1 - ch.16)
00H - 7FH (0 - 127)
00H - 7FH (0 - 127)
3rd byte
vvH
0H - FH (ch.1 - ch.16)
00H - 7FH (0 - 127)
01H - 7FH (1 - 127)
3rd byte
vvH
0H - FH (ch.1 - ch.16)
00H - 7FH (0 - 127)
00H - 7FH (0 - 127)
3rd byte
mmH
llH
0H - FH (ch.1 - ch.16)
00 00H - 7F 7FH (bank.1 - bank.16384)
3rd byte
vvH
0H - FH (ch.1 - ch.16)
00H - 7FH (0 - 127)
Publicité
Table des Matières
