Installing The Cooker Hood - Pando E-320 Instructions D'utilisation

INSTALLING THE
COOKER HOOD
1. Before carrying out the appliance installation,
please check that all components are not da-
maged, in such a case contact your retailer
and do not carry out any installation operation.
Before the installation of the Downdraft, ple-
ase remove the safety piece you can see in
the picture (Fig. 1). Furthermore, please read
carefully all of the following installation instruc-
tions.
● Use an air exhausting pipe whose maximum
length does not exceed 5 meters.
● Limit the number of elbows in the piping,
since each elbow reduces the air capacity of
1 linear meter. (Ex. : if you use no. 2 x 90 °
elbows, the length of piping should not exceed
3 meters).
● Avoid abrupt direction changes.
● Use a 150 mm. constant diameter pipe for
the whole length.
● Use piping approved by standards in force.
The manufacturer shall not be deemed re-
sponsible for air capacity or noise problems
caused by failure to comply with the above
instructions and no warranty on the product
shall be provided.
2. Before making the hole, check that there are
no structural or other parts inside the cabinet,
where the appliance is to be placed, which
could hinder a proper installation.
Check that the dimensions of the Downdraft
and the ones of the cook top are compatible
with the cabinet so that the installation can be
carried out properly.
3. Make a rectangular opening in the back part
of the cook top (842x100 mm for the 90 cm
model and 542x100 mm for the 60 cm model
and 1142x100 mm for the 120 cm model).
In the version with the motor already installed,
remove the screws and the suctioning unit in
order to insert the downdraft in the hole made.
E-320
EN
4. Put the Downdraft in the opening, inserting it
from above as shown in (Fig. 2).
5. Fix the downdraft inside the cabinet, using the
special fixing brackets supplied with the pro-
duct (Fig. 3).
Insert the brackets in the lower side of the
downdraft (Fig. 3), in such a way that there
is a 2 mm distance between the lower side of
bracket and the bottom of the cabinet (Fig. 3).
This distance will allow the traction to be po-
sitioned downwards of the product, at the mo-
ment of fixing, in order to have the stainless
steel trim perfectly adhering with the work
surface. Before inserting the screws, please
make sure that the appliance is perfectly per-
pendicular with the work surface.
6. Once the installation is complete and after
connecting the appliance to the mains power,
lift up the downdraft and remove the door
block (Fig. 4); then open the door (Fig. 5) and
fit the filters in place (Fig. 6). In the version
of the Downdraft equipped with internal motor,
install the power unit orienting the air outlet to
the desired position, either downwards or up-
wards (Fig. 7).
The motor can be installed either on the front
or rear side of the downdraft After having in-
stalled the motor, connect the air ducts.
7. For versions with external motor, place the
suctioning unit (external motor) in a suitable
area and fit the exhaust air flue as illustrated.
Then fit the air outlet ducts between the ex-
ternal motor and the downdraft. Select an air
outlet from the five possibilities (Fig. 9) and fit
the union supplied with the appliance.
8. Place the metal box containing the wiring in an
easily accessible area to allow maintenance
interventions where necessary (Fig. 9). Con-
nect the connectors (9-pole connector to con-
trol the actuator and safety control and button
pad connector) (Fig. 10).
9.
Connect the internal motor or the external mo-
tor's cable to the terminal board found inside
the plastic box of the downdraft wiring . Make
sure to respect the colors of cables when per-
forming the electrical connection (fig.25).
21