EdilKamin SIDE 50x50 PLUS N Installation, Usage Et Maintenance page 27

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 32
Smoke channel
Smoke channel
The smoke channel is the duct which connects the fume exit
The smoke channel is the duct which connects the fume exit
vents of the replace with the ue entrance.
vents of the replace with the ue entrance.
The smoke channel must be made of rigid pipe in steel or
The smoke channel must be made of rigid pipe in steel or
ceramic material; exible pipes and pipes in asbestos cement
ceramic material; exible pipes and pipes in asbestos cement
are not allowed.
are not allowed.
Horizontal or downward sloping sections must be avoided.
Horizontal or downward sloping sections must be avoided.
Any difference in section is allowed only at the replace exit
Any difference in section is allowed only at the replace exit
and not, for example, at the connection point in the ue.
and not, for example, at the connection point in the ue.
Angles of more than 45° are not allowed.
Angles of more than 45° are not allowed.
The point where the steel ue is connected to the fume exit
The point where the steel ue is connected to the fume exit
vent of the replace must be sealed with heatproof mastic.
vent of the replace must be sealed with heatproof mastic.
In addition to the above, it is also necessary to take into
In addition to the above, it is also necessary to take into
consideration the indications of paragraph 4.2 and sub-
consideration the indications of paragraph 4.2 and sub-
paragraphs of standard UNI 10683 "connecting to the fume
paragraphs of standard UNI 10683 "connecting to the fume
evacuation system".
evacuation system".
Flue and chimney
Flue and chimney
The ue is the duct from the room in which the replace is t-
The ue is the duct from the room in which the replace is t-
ted which eventually reaches the roof of the building.
ted which eventually reaches the roof of the building.
INSTALLATION
Basic features of the ue
Basic features of the ue
The ue must conform to the standard UNI EN 1443 and it
The ue must conform to the standard UNI EN 1443 and it
must be installed according to standard UNI EN 10683; the
must be installed according to standard UNI EN 10683; the
ue:
ue:
- must be of temperature class T450 or higher and ash re
- must be of temperature class T450 or higher and ash re
resistance class Gxx
resistance class Gxx
- must have the capacity to stand a temperature of at least
- must have the capacity to stand a temperature of at least
450°C as regards mechanical resistance, insulation and air
450°C as regards mechanical resistance, insulation and air
tightness
tightness
- must have suitable insulation to avoid the formation of con-
- must have suitable insulation to avoid the formation of con-
densation - with constant section, practically vertical position
densation - with constant section, practically vertical position
and without angles of more than 45%
and without angles of more than 45%
- must have preferably circular internal sections; in the case
- must have preferably circular internal sections; in the case
of rectangular sections, the maximum ratio between the sides
of rectangular sections, the maximum ratio between the sides
must not exceed 1.5
must not exceed 1.5
- must serve only one replace (or stove).
- must serve only one replace (or stove).
In the case of ues that are not new and not particularly large,
In the case of ues that are not new and not particularly large,
it is advisable to t an inner pipe in stainless steel with a suit-
it is advisable to t an inner pipe in stainless steel with a suit-
able diameter and suitable insulation. In the case of a ue
able diameter and suitable insulation.
longer than 5 metres, it is advisable for the installer to t a
longer than 5 metres, it is advisable for the installer to t a
draught regulation damper.
draught regulation damper.
Basic features of the chimney:
Basic features of the chimney:
- internal section at the base equal to that of the ue
- internal section at the base equal to that of the ue
- exit section no less than double that of the ue
- exit section no less than double that of the ue
- position in full wind, above the roof and beyond the re ux
- position in full wind, above the roof and beyond the re ux
area.
area.
- 27
-
In the case of a ue

Publicité

Chapitres

Table des Matières
loading

Ce manuel est également adapté pour:

Side 50x50 plus v

Table des Matières