Publicité
Les langues disponibles
Les langues disponibles
START-UP AND PROGRAMMING
START-UP
5g
1 - Plug in the power socket. Wait 20 seconds: appliance
initializing. Open the water tap to rinse well. Start the
normal flush by pressing the dark grey button. Put
a few sheets of toilet paper down in the bowl and flush
again.
Note:
This unit does not need to be vented.
2 - Turn on the sink tap. The unit should sink activate
automatically.
3 - Demount the bowl and check the water tightness of all
connections.
WARNING:
Leaking faucets will cause the unit to
4 -
activate automatically.
PROGRAMMING
5h
The length of your SANICOMPACT
to which cycle you choose.
Eco flush (by default, light grey button):
19 seconds and 1 gallon (3.8L): rinsing of the bowl for 10
seconds, the pump works for 7 seconds (for 7 seconds, the
bowl continues to fill), then the bowl fills again for 2 seconds.
You can lengthen the first rinse of the eco flush to 16
seconds if the default flush is not enough.
Normal flush (dark grey button):
25 seconds and 1.32 gallons (5L): The bowl is rinsed for 16
seconds, the pump works for 7 seconds (for 7 seconds, the
bowl continues to fill) then the bowl fills again for 2 seconds.
To re-program:
Note:
Only the ECO option can be reprogrammed.
• Hold the ECO button (light grey button) down for 5
seconds.
• The motor works for 2 seconds, this means you have ente-
red programming mode.
• Each time you press the dark grey button you increase the
length of the ECO flush by 1 second: each time you press it
will be validated by the motor running for a short period.
• Each time you press the grey button you decrease the
length of the flush by 1 second: each time you press it will
be validated by the motor running for a short period.
To exit programming mode:
• Wait for 5 seconds without pressing any buttons.
The motor runs for 2 seconds, this means that you have
left programming mode.
Comment 1: the minimum length of the first rinsing flush for
the normal flush is 19 seconds (default programming)
and the maximum length is 25 seconds.
Comment 2: the normal flush cannot be modified.
USAGE
5i
1 - The SANICOMPACT
®
require any special maintenance.
2 -
WARNING:
The SANICOMPACT
for the evacuation of normal human waste, toilet
paper and household toilet cleaners.
Damage may occur to the motor if the following
are disposed of via the toilet: cotton wool, tampons,
sanitary napkins, wet wipes, kitchen towels,
condoms, dental floss as well as other fabric or hard
objects. Solvents, acids and other chemicals can
also cause damage to the unit, and will invalidate the
warranty.
3 -
WARNING:
In case of prolonged power failure, or
going on vacation, please close the stop valve of the
the sink and water supply.
RETURN OF THE UNIT
5j
In the unfortunate event that the SANICOMPACT
defective and has to be returned for service, we suggest
to remove the macerating/pump from the porcelain bowl.
Please ensure that it has been thoroughly cleaned and
disinfected inside and outside prior to packaging for dis-
®
's flush varies according
pump/macerator does not
®
should only be used
®
patch. Do not submerge the motor completely in water; the
electrical components might be damaged beyond repair.
DISMANTLING AND REMOVING THE MOTOR FROM
5k
THE TOILET
FOR QUALIFIED PERSONNEL ONLY
1. Disconnect the SANICOMPACT
supply.
2. Close the Shut-Off valve and disconnect toilet supply
tube.
3. (If installed) Close Gate or Ball Valve and disconnect
from discharge pipe system.
4. Current model the screws holding the Sanicompact are
on the sides.
5. In the rear of the unit, look for a clear plastic hose going
from the solenoid valve to a black elbow in the top of
the bowl. With a twisting motion pull the black elbow out
of the porcelain.
6. In the rear of the unit, look for a large rubber elbow,
going from the motor to the p-trap of the toilet. Unscrew
the gear clamp near the motor (holding the rubber
elbow).
7. The motor is assembled in the reverse of the above.
Special Note for Service People:
blade and motor mechanism, a Torx (#20) bit will be nee-
ded to remove the cover. There are 12 screws holding
the case cover. In order to inspect the capacitors, circuit
board and electronics, Triwing (#3) bit will be needed. Only
four screws hold this cover.
IMPORTANT / SERVICE
Before returning the motor to the factory, a return
authorization is needed from the manufacturer since some
repairs may be done in the field. Parts or motors send in
for repair, must be send pre-paid. Units sent collect and/or
sent without prior authorization, will be refused.
Package the macerating/pump unit properly with adequate
shock absorbent material around it. Send package prepaid
to the manufacturer, making sure to insure against loss
and/or transit damage, (the amount of $ 250.00 will
suffice).
If any repairs are done outside the warranty period, or when
the user damages the macerating/pump unit, an estimate
of repair cost will be communicated to the customer. All
repairs (parts and labour) will be done on a pre-paid basis
only.
is
®
from the electrical
In order to inspect the
Publicité
