Troubleshooting; Power Indicator Is Not Illuminated; Fuse Replacement; No Sound - Rotel RMB-1555 Manuel De L'utilisateur

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 12

Troubleshooting

Most difficulties in audio systems are the result of incorrect connections,
or improper control settings. If you encounter problems, isolate the area
of the difficulty, check the control settings, determine the cause of the fault
and make the necessary changes. If you are unable to get sound from the
amplifier, refer to the suggestions for the following conditions:

Power Indicator Is Not Illuminated

No main power to the amplifier. Check the front panel power switch. Make
sure that it is set to the on position. Check AC power connections at the
amplifier and the AC outlet.

Fuse Replacement

If another electrical device works when plugged into the power outlet, but the
Power Indicator of the unit does not light when plugged into the same outlet
and the Power Switch is pushed in, it indicates that the internal power fuse
may have blown. If you believe this has happened, contact your authorized
Rotel dealer to get the fuse replaced.

No Sound

If the amp is getting AC power, but is producing no sound, check the
Protection indicator on the front panel. If it is lit, see below. If not, check all
of your connections and control settings on associated components.
Protection Indicator
The front panel POWER indicator is blinking when the amplifier protection
circuits have shut off the amplifier. Typically, this occurs only when the
ventilation openings are blocked, when there is faulty speaker wiring, or
after a period of extreme use. Turn off the system and wait for the amp to
cool. Then push the front panel power switch in and out to reset the protection
devices. If the problem is not corrected or reoccurs, there is a problem with
the system or the amplifier itself.

Specifications

RMB-1555
Continuous Power Output
(20-20kHz, < 0.03%, 8 ohms)
Total Harmonic Distortion
(20Hz-20kHz, 8 ohms)
Intermodulation Distortion (60Hz : 7kHz, 4:1)
Frequency Response (+0.5, –3dB)
Damping Factor (20-20kHz, 8 ohms)
Speaker Impedance
Signal to Noise Ratio (IHF A network)
Input Impedance/Sensitivity
Gain
Power Requirements
U.S. version
European version
Power Consumption
Dimensions
Width x Height x Depth
Front Panel Height
Weight (net)
RMB-1585
Continuous Power Output
(20-20kHz, < 0.03%, 8 ohms)
Total Harmonic Distortion
(20Hz-20kHz, 8 ohms)
Intermodulation Distortion (60 Hz : 7 kHz, 4:1)
Frequency Response (+0.5, –3dB)
Damping Factor (20-20kHz, 8 ohms)
Speaker Impedance
Signal to Noise Ratio (IHF A network)
Input Impedance/Sensitivity
Unbalanced
Balanced
Gain
Power Requirements
U.S. version
European version
Power Consumption
Dimensions
Width x Height x Depth
Front Panel Height
Weight (net)
All specifications are accurate at the time of printing.
Rotel reserves the right to make improvements without notice.
Rotel and the Rotel HiFi logo are registered trademarks of The Rotel Co, Ltd., Tokyo, Japan.
11
120 watts/channel,
5 channels dirven
< 0.03%
< 0.03%
10Hz - 100kHz
180
4 ohms minimum
116 dB
12k Ohms/1.5 volt
26.5 dB
120 Volts, 60Hz
230 Volts, 50Hz
650 Watts
431 x 188 x 454 mm
17 x 7
/
x 17
/
ins.
1
7
2
8
4U / 176.8mm / 7 ins.
21.8kg / 48.1 lbs.
200 watts/channel,
5 channel driven
< 0.03%
< 0.03%
10Hz - 100kHz
260
4 ohms minimum
116 dB
12k Ohms/1.9 volt
100k Ohms/3.8 volt
26.5 dB
120 Volts, 60Hz
230 Volts, 50Hz
1100 Watts
431 x 237 x 454 mm
17 x 9
3
/
x 17
7
/
ins.
8
8
5U / 221mm / 8
3
/
ins.
4
36kg / 79.3 lbs.

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Rmb-1585

Table des Matières