Conditions Of Warranty - Saitek Mephisto Pro Bridge 610 Mode D'emploi

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 38

CONDITIONS OF WARRANTY

1. Warranty period is 2 years from date of
purchase with proof of
purchase submitted.
2. Operating instructions must
be followed.
3. Product must not have been
damaged as a result of
defacement, misuse, abuse,
neglect, accident, destruction or
alteration of the serial number, improper
electrical voltages or currents, repair,
alteration or maintenance by any person or
party other than our own service facility or
an authorized service center, use or
installation of non-Saitek replacement parts
in the product or the modification of this
product in any way, or the incorporation of
this product into any other products, or
damage to the product caused by accident,
fire, floods, lightning, or acts of God, or any
use violative of instructions furnished by
Saitek plc.
4. Obligations of Saitek shall be limited to
repair or replacement with the same or
similar unit, at our option. To obtain repairs
under this warranty, present the product
and proof of purchase (e.g., bill or invoice)
to the authorized Saitek Technical Support
Center (listed on the separate sheet
packaged with this product) transportation
charges prepaid. Any requirements that
conflict with any state or Federal laws, rules
and/or obligations shall not be enforceable
in that particular territory and Saitek will
adhere to those laws, rules, and/or
obligations.
5. When returning the product for repair,
please pack it very carefully, preferably
using the original packaging materials.
Please also include an explanatory note.
6. IMPORTANT: To save yourself unnecessary
cost and inconvenience, please check
carefully that you have read and followed
the instructions in this manual.
7. This warranty is in Lieu of all other
expressed warranties, obligations or
liabilities. ANY IMPLIED WARRANTIES,
OBLIGATIONS, OR LIABILITIES,
INCLUDING BUT NOT LIMITED TO THE
IMPLIED WARRANTIES OF MERCHANT-
ABILITY AND FITNESS FOR A PARTICU-
LAR PURPOSE, SHALL BE LIMITED IN
DURATION TO THE DURATION OF THIS
WRITTEN LIMITED WARRANTY. Some
states do not allow limitations on how long
an implied warranty lasts, so the above
limitations may not apply to you. IN NO
EVENT SHALL WE BE LIABLE FOR ANY
SPECIAL OR CONSEQUENTIAL
DAMAGES FOR BREACH OF THIS OR
ANY OTHER WARRANTY, EXPRESS OR
IMPLIED, WHATSOEVER Some states do
not allow the exclusion or limitation of
special, incidental or consequential
damages, so the above limitation may not
apply to you. This warranty gives you
specific legal rights, and you may also have
other rights which vary from state to state.
Information for Customers in the United
States:
FCC Compliance and Advisory Statement
Warning: Changes or modifications to this unit
not expressly approved by the party
responsible for compliance could void the
user's authority to operate the equipment.
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful
interference, and
2. This device must accept any interference
received, including interference that may
cause undesired operation
NOTE: This equipment has been tested and
found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses and can radiate
radio frequency energy and, if not installed
and used in accordance with the instructions,
may cause harmful interference to radio
communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or
television reception, which can be determined
by turning the equipment off and on, the user
is encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving
antenna.
• Increase the separation between the
equipment and receiver.
• Connect the equipment into an outlet on a
circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced
radio/TV technician for help.
Saitek Industries, 2295 Jefferson Street,
Torrance, CA 90501, USA
20
20

Publicité

Table des Matières
loading

Table des Matières