Technical Data; General Safety Instructions - EUROM EK3000prof Manuel D'utilisation

Technical data

Type
Supply voltage
Maximum capacity
Settings
Air flow
Air speed
Insulation class
Dimensions
Weight

General safety instructions

1. Before using the machine, carefully read this entire instruction manual.
2. Before using your new heater, check it, including cord and plug, for any visible damage. Do not use a
damaged heater, but send it back to your dealer for replacement.
3. This heater is exclusively intended to heat workspaces such as workshops, garages, storage spaces,
construction sites etc. Use the appliance for this purpose only.
4. Under the terms and conditions described in this leaflet, the heater can be used in wet or damp indoor
spaces such as bathrooms and laundry rooms. Do not place the heater in the vicinity of taps, bathtub,
shower, pool, fountains or other sources of moisture (↔ > 1m.). Make sure it cannot fall into water, Also make
sure that it cannot come into contact with jets of water, splashes, etc. and prevent water from getting into the
heater itself. If, at any time, the heater does fall into water, unplug it immediately! Do not use a heater that
has a damp interior but have it repaired. Never immerse the heater, cord or plug in water and never touch it
with wet hands.
5. The supply voltage and utility frequency, specified on the machine, need to match those of the socket that is
used. The electrical installation needs to be protected by a residual current device. If the plug does not fit
exactly, you should consult a qualified electrician. Never attempt to find a way round the safety features!
6. Fully extend the cord before plugging in the heater. Make sure it does not come into contact with any part of
the heater and prevent it from heating up any other way. Do not run the cord underneath carpeting; do not
cover it with mats, carpet strips or similar and make sure it is not placed in any passageways. Make sure the
cord cannot be stepped on and that no furniture is placed on top of it. Do not lead the cord around sharp
corners and do not roll it up too tightly after use!
7. If possible, do not use an extension cord, as this poses the risk of overheating and fire. If the use of an
extension cord is unavoidable, then make sure it is an undamaged, approved 3-core extension cord with a
minimum diameter of 2.5 mm², suitable for a minimum permissible power of 4000 (EK3000prof) / an
undamaged, approved 4-core extension cord with a minimum diameter of 2.5 mm², suitable for a minimum
permissible power of 13.000 (EK12000prof) Watt. To prevent overheating, always fully extend the cord!
Never use a single extension lead for more than one fan-heater, or for one fan-heater and another item of
electrical equipment!
8. To prevent the circuit overloading and fuses being blown, make sure no other appliances are connected to
the same socket or wired to the same electrical circuit as the heater.
9. Do not use the heater outdoors and do not use it in spaces smaller than 9 m² (EK3000prof) / 36 m²
(EK12000prof) .
10. A heater contains hot and/or glowing and sparking components. Do not, therefore, use in areas where fuels,
paint, flammable liquids and/or gasses etc. are stored.
11. Do not place the heater near, under or directly opposite a socket and do not place it near an open fire or
other heat source.
12. Do not use the heater near or directly opposite furniture, animals, curtains, paper, clothes, bedding or other
inflammable objects. Keep them at least 2 metre away from the heater!
13. Never cover a heater! The heater's air inlets and outlets should never be obstructed in any way, so as to
prevent the possibility of fire. Never use the heater to dry clothes and do not place anything on top of the
heater. Do not place it on soft surfaces such as beds or deep-pile carpets, as they can block openings.
14. Make sure that the air around the heater can circulate freely. Do not place the heater too close to walls or
large objects and do not place it under shelves, cupboards, and similar.
15. Prevent foreign objects from entering the heater via the venting or exhaust openings as this may lead to
electric shock, fire or damage.
English
EK3000prof
Volt/Hz 230 / 50
kWatt 3
0 – fan - 1,5 – 3
kWatt
m³/h 22.320
m/sec 6,2
IP24
cm 35 x 30 x 35
kg 9
EK12000prof
400 / 50
12
0 – fan – 6 – 9 - 12
27.000
7,5
IP24
61 x 38 x 45
22
9