Publicité
RESIDENTIAL INSTALLATION WITH X2 BLOCKS
X2 Block - 2
X2 Block X2 - 1
Master
XA/300LR
ICB/300
XAV/300
HPV/1+
HAV/200+
HIA/300+
ICP/LR+
...HEP/306+
...HTS
Master and Slave entry panels:
HEV/301, HEC/301, HET/301, AZV/304, AZ/304.
X2 block
entry
panel
Master
X2 block
entry
panels
Slave
Slave
Slave
IPD/300LR
Porter
switchboard
300 entry panels
HPV/1+
HAV/200+
HIA/300+
1
2
3
4
5
6
HAC/300LR+
7
8
9
0
C
2HTS
P
S
T
entry panel, two procedures are
necessary, given below.
A - Identification of block entry
panel.
B - Setting of number of user calls
in the block.
A - Identification
of block entry panel
1 - Remove and replace jumper
SW2 (receiver programming mode)
on the first Master entry panel only
(the one connected to the XA/300LR
power supplier, fig. 3) belonging to
the first X2 block and await confir-
mation;
confirmed by double audible signal
and the solenoid door lock release
command being activated.
B - Definition of number
of user calls in the block
This programming is performed,
again from the Master entry panel,
proceeding as follows:
1 - Set number of buttons used on
audio/video panel (0, 1, 2, 3 or 4):
- press the last button used on the
audio/video panel (fig.4); if there isn't
one, press the first button on the
additional panel (fig.4).
2 - Set total number of user calls in
the block:
- press the last call button used.
Audio/video panel
Additional
(max 4 buttons)
panel
HEV/301
HEP/306
HET/301
HEP/312D
HEC/301
VZS/308C
AZV/304
or digital
AZ/304
HAC/300LR
2.5 - Repeat the procedure in point
2.4 for the following first Master entry
panels belonging to the other blocks.
Programming of other Slave entry
panels belonging to the same block
(fig. 3) must be performed afterwards
(see "Programming X2 Slave entry
panels" section).
2.6 - Exit programming mode.
Sample settings of number
of user calls
EXAMPLE 1 - X2
block
Targha audio-only entry panel with 3
calls, with no additional pushbutton
panels (fig. 5).
1A
3
1 - Press call button n.3 (position 1A)
to set the number of buttons used (3)
on the audio/video panel.
Wait for audible confirmation (*).
2 - Press the same button again to
set the total number of user calls in
the block (3).
Wait for audible confirmation (*).
EXAMPLE 2 - X2
Targha audio-only entry panel with 10
calls
and
additional
panels (fig. 6).
1B
1 - Press call button n.4 (position 1B)
to set the number of buttons used (4)
on the audio/video panel.
Wait for audible confirmation (*).
2 - Then press call button n.10 (posi-
tion 2B) to set the total number of
user calls in the block (10).
Wait for audible confirmation (*).
EXAMPLE 3 - X2
Targha entry panel with camera with
12 calls and additional pushbutton
panels (fig. 7).
1C
4
1 - Press call button n.1 (position 1C)
to set the number of buttons used (0)
on the audio/video panel.
Wait for audible confirmation (*).
2 - Then press call button n.12 (posi-
tion 2C) to set the total number of
user calls in the block (12).
featuring
Wait for audible confirmation (*).
EXAMPLE 4 - X2
entry panel with AZ/304 or AZV/304
5
block
featuring
pushbutton
2B
6
block
featuring
2C
7
block
featuring
1D
8
5
Publicité
