THOMSON ROC1128PAN Mode D'emploi page 2

INPUT
LINK
EXIT
INDEX
ASPECT
AAA
Replacement Remote for
2. Package Contents
• Replacement Remote Control
PANASONIC SERIES: TV/LCD/LED/HDTV
• 2x AAA Batteries
• This operating instructions incl. Code List
3. Safety notes
• Do not use the Universal Remote Control in
Thank you for your decision for a Thomson product.
moist or wet environments and avoid spray-
Take your time and read the following instructions
water contact.
and information completely. Please keep these
• Do not expose the Universal Remote Control
instructions in a safe place for future reference.
to heat sources or direct sunlight.
This remote control can by default control 90%
• Do not drop the Universal Remote Control.
models of PANASONIC brand, there´s no need to
• Never open the Universal Remote Control. It
set it up. lf the remote doesn't work, please choose
contains no user-serviceable parts.
one of the setup methods described in chapter 5.
• As with all electrical devices, keep the
Universal Remote Control away from
The keys
children.
1. Power TV ON/OFF
2. Turn your TV sound ON/OFF
Warning
3. TV Mode
4. AV Mode
5. APPS
• When inserting batteries, note the
6. LINK
correct polarity (+ and - markings) and
7. Show the Electronic Program Guide insert the batteries accordingly. Failure to
(if supported by the TV) do so could result in the batteries leaking
8. Tools menu or exploding.
9. HOME
• Do not short-circuit batteries.
10. Exit Menu
• Do not charge batteries.
11. Menu
• Do not throw batteries in a fire.
12. Internet
• Keep batteries out of the reach of
13. SD/USB Mode
children.
14. Option and Tools
15. Back key • Do not allow children to change batteries
16. Enter without supervision.
17. Use when watching TV to see what´s on
• Remove the batteries from products
other channels or to highlight/select On-
that are not being used for an extended
Screen options
period.
18. Use to select a variety of on screen options
19. Volume + / -
4. Getting started – installing the Batteries
20. Program +/-
21. Teletext ON/OFF
Note
22. Teletext Subtitle
23. Teletext Info
24. Teletext Hold • Use 2 AAA batteries
25. Numeric keys 0 – 9 to enter channel numbers
• Remove the battery cover from bottom
26. Access to 2- or 3-digit channel numbers
of remote.
27. Previous Channel
• Check the +/- polarity on the batteries
28. Info
and inside the compartment.
29. Normal
• Insert the batteries.
30. Picture Size
• Slide the battery holder back into the
31. Goes backward (DVD, BlueRay ... )
remote until the clips locate.
32. Play a disc (DVD, BlueRay ... )
33. Fast Forward (DVD, BlueRay ...)
34. Player Preview (DVD, BlueRay ...)
Note – Code Memory
35. Player Next (DVD, BlueRay ...)
36. Suspends play and stops on an image
This remote control saves the settings during
(DVD, BlueRay...)
battery change.
37. 3D Mode ON/OFF
38. Stop the disc (DVD, BlueRay ... )
39. Record
5. Setup
This remote control can by default control 90%
1. Explanation of the Note and Warning
models of PANASONIC brand, there´s no need
symbol
to set it up. lf it doesn't work, please choose
one of the following setup methods 5.1 or 5.2.
Warning
5.1 INPUT CODE
This symbol is used to indicate safety instructions or
CODE List:
to draw your attention to specific hazards and risks.
001, 002, 003, 004, 005, 006, 007, 008,
009, 010, 011, 012, 013, 014, 015, 016,
Note
017, 018, 019, 020, 021, 022, 023, 024,
025, 026, 027, 028, 029, 030, 031, 032,
This symbol is used to indicate additional
033, 034, 035, 036, 037, 038, 039, 040,
information or important notes.
041, 042, 043, 044, 045, 046, 047, 048
2
1. Press and hold the key [MUTE] and 5.5 Resetting to factory settings
[POWER] until the LED will be lit,
Press and hold the [RETURN] and [0] buttons for
then release keys.
about 5 seconds until the status LED flashes three
times and then goes out. The remote control is
now successfully reset to the factory settings.
Note
2. Enter the three codes from code Iist.
All keys with learnt codes or all copied keys,
When the code input is finished, the
as well as all remote control settings will
LED will turn off.
be deleted.
6. LEARN MODE
This remote control is equipped with a learning
function. Thus, you could learn functions of
LAST
your original remote to this remote control.
3. Please try to use the remote control.
lf it doesn't work well, please try other
6.1 BEFORE STARTING LEARN MODE
codes: [002], [003], [004] ...
• The batteries in the two remote controls
have to be in good condition. Replace them
if necessary.
Note
• Place the remote controls with the infrared
diodes so that they point towards each
lf the code is invalid, the LED flashes twice
other.
and then lights up permanently. To exit the
• Where necessary adjust the height of both
setup, please press [MUTE].
remotes so that infrared diodes are properly
aligned.
5.2 FAST SEARCH
• The distance between the remote controls
1. Press and hold the key [MUTE] and
should be about 3 cm.
[POWER] until the LED will be lit, then
release keys. ROC1128PAN
Note
2. Press the key [CH+]. Each time you
press, the remote will search once.
• Do not move the remote controls during
When the code changes, you can test
the learning procedure.
if [POWER], [VOL+],[MENU],[0-9] keys
work well. If ok ,please press [ MUTE] to • Ensure that the room is not lit by
save the code and exit. fluorescents tubes or low energy
3. lf it doesn't work well, repeat the fast consumption lamps since such light
search by pressing [CH+]. sources could interfere with the copying.
• The 2 remote controls must be at least
5.3 CODE INQUIRY 1 meter away from any light source.
Use the following method to find out which • During learning mode, if no key is
code is currently set: selected for more than 15 seconds, the
learning mode will exit automatically or
1. Press and hold [MUTE], then press
if no other remote signal is received.
[POWER] until the LED will be lit, then
• Each function key will hold only one
release keys.
command. A new command to be learned
2. Input [9].[9].[0] with number keys. The
will automatically replace the previous one.
LED will flash twice and goes off.
3. Press the number key 1 for the 1st digit
6.2 ENTER LEARN MODE
of the code. The LED will start to flash.
1. Press and hold the [MUTE] and [VOL+]
Count the LED flashes. The number of
keys for approx. 5 seconds until the LED
flashes resemble the code's first digit.
will be lit.
Repeat this procedure for the 2nd and
3rd digit of the code:
2nd digit -> enter 2 -> count LED
flashes
3rd digit -> enter 3 -> count LED flashes
2. Enter the code [9] [8] [0], the LED will flash
lf code number is [0] the LED will not
2 times and then remain on.
flash.
3. The remote control is now ready to learn
new commands.
5.4 Compatible Remote Control Model
Due to too many Remote Control models, we
6.3 LEARNING OF KEYS
only Iist some of them below. lf your remote
1. Press and release the desired key on the
control is similar to the drawing, the replacement
original remote control which you want the
remote can control your TV (Page 74)..
command to be learned. The LED at your
replacement remote will flash to confirm
that the information has been received.
3
ORIGINAL
ca. 3 cm
5