Steam Function; Coloured Light; Water; Audio - HOESCH SenseSation Instructions De Montage Et D'utilisation

■

Aroma

■

Infrared

■

Programs

■

Service settings

04.01 Steam function

You can choose and regulate temperature and steam bath time by
using "steam bath" section in the menu.
You can select exact temperature and time by using the
button, and then adjust with [-] and [+] button.
The temperature adjustment range is between 25 °C and 50 °C.
Steam bath time can be regulated from 0 to 90 minutes (in
intervals of 5 minutes).
During steam operation current temperature inside the cabin, time
remaining and set temperature will be displayed.

04.02 Coloured light

The function Coloured light is activated / deactivated by pressing
[OK] button in the main menu.
Pressing [menu] button you can enter the submenu where you
can activate the "coloured light pass" with [ok] button and adjust
the ''speed of the coloured light pass" with scale from 1 (fast) to 4
(slowly).
GB
By deactivating the colour light pass you stop this run and it
remains the least adjusted light colour.

04.03 Water

In the menu item Watter both side nozzles and rain shower can
be controlled.
The side jets are divided into two zones and can be controlled
separately or combined. The subitem "Side jets 1" describes the
top 4 side jets, the subitem "Side jets 2" stands for the 4 side jets
beneath.
The rain shower can only be used separately from the side jets.
All subitems are activated or deactivated by pressing the [OK]
button.

04.04 Audio

In the submenu the items "Radio FM", "MP3/WMA" or "Aux In"
can be controlled.
Radio: station-search run. Using
previous and next station respectively.
MP3/WMA: Firsty a corresponding storage device must be
connected to the USB port in the wall installation profile. Using
and buttons you can select the previous and next music title
respectively. Pressing [menu] button you can enter the submenu,
where "Next folder" and "Random selection" using [ok] button can
be activated / deactivated.
AUX In: Connected, external signal sources can be controlled
using a chich-connector. The volume is set using [-] and [+]
buttons.
04.05 Aroma
The function "Aroma" is
activated / deactivated by
pressing [OK] button in
the main menu.
Using [menu] button
you can enter the sub
items "Aroma" (in %),
"Fragrance dispencer"
and "Filling".
Pressing the fi rst sup
item and using [+] and
[-] buttons you can set
the aroma's intensity in
intervals of ten between 10 % and 100 %. The factory default
value is 100 %.
The fragrance dispencer is activated / deactivated using [ok]
button. Through these you can enjoy the desired aroma even
without the steam function.
12
and
and buttons you can set
Before you activate the fi lling, please ensure that the suction hose
is placed in the appropriate recervoir with aroma. As soon as you
activate the fi lling using [ok] button, the process starts. Filling
stops automatically, as soon as the internal sensor signs fully fi lled
aroma recevoir.
04.06 Infrared
The function infrared (IR) is activated / deactivated in the main
menu using [OK] button.
In the submenu of this function you can set the "IR-intensity" and
the "IR-duration".
The IR-intensity is adjusted by means of different intensity levels
and ranges between 1 (low intensity) and 6 (high intensity). The
selection of the appropriate intensity occurs via [+] and [-] buttons.
The adjustment range of the IR-duration is between 0 and 90
minutes. The adjustment occurs via [+] and [-] buttons in 5 minute
increments.
04.07 Programs
You can program four different programs (program 1-4) in
"Programs" subsection in the main menu.
By pressing [menu] button you select eg. "program 1" and can
program the beginning and the end of your steam bath.
At the same time, you can set the fragrance function, if required.
You can select steam bath start up and fi nish time in 24 hours
format by using [-] and [+] button.
Aromatherapy is turned on/off with [OK] button.
If one or more programs are active, and the control panel is
switched into standby mode with
message appears: "Warning! Running programs are active".
04.08 Service settings
In the are of "Service" you can set confi guration, clock, aroma
control and manual decalcifying.
Using and buttons you can use menu functions. With
"menu" button, you enter sub-menu, and with "exit" button you
return back to service menu.
04.08.1 Confi gurations
By pressing the [menu] button you can enter the sub items
"contrast" and "language". They can be than selected using
and buttons.
Display contrast can be adjusted from 0-40 by using [-] and [+]
button. The factory default value is 20.
Language can be selected by using [-] and [+]button. You can
choose one of the following language versions: German, English.
French, Dutch, Spanish, Italian, Polish, Russian or Chinese. The
factory is set to German language version.

04.08.2 Clock

Under the menu item "clock" you can set both "time" and "12 hour
clock".
In order to set the time, choose the required function with
buttons and then, set hour and minutes by using [-] and [+]
button.
To select or cancel 12-hour format, use the
then choose appropriate subsection and confi rm with [ok] button.

04.08.3 Aromatherapy control

Aromatherapy control submenu (impulse time, impulse duration,
minimal temperature required) is chosen
with and buttons which are selected by pressing [OK]
button. All settings can be adjusted with [-] and [+] button. Impulse
time can be regulated from 0 to 600 seconds, factory setting is
300 seconds. Impulse duration can be regulated from 100 to 5000
ms, factory setting is 1000ms. Minimal temperature required can
be regulated from 30°C to 50 °C, factory setting is 30°C.
button, the following
and
and buttons