Description Of Device / Spare Parts; Assembly; Preparing For Commissioning - ATIKA T 250 N-2 Notice Originale

Do not set up any provisional electrical connections.
Never bypass protective devices or deactivate them.
Only hook up the machine by means of a fault-current circuit
breaker (30 mA).
The electrical connection or repairs to electrical parts
of the machine must be carried out by a certified
electrician or one of our customer service points.
Local regulations – especially regarding protective
measures – must be observed.
Repairs to other parts of the machine must be carried
out by the manufacturer or one of his customer
service points.
Use only original spare parts and accessorie parts.
Accidents can arise for the user through the use of
other spare parts. The manufacturer is not liable for
any damage or injury resulting from such action.

Description of device / spare parts

Pos.-
Order-No. Denomination
No.
2 366272 Supporting leg
3 366282
Connection strut – short
4 366280
Connection strut – long
5 366266 Saw blade
6 Crank for height adjustment
7 366256 Safety guard
8 366260 Splitting wedge
9 366261 Extraction hose
10 Bench plate
11 366254 Transverse stop cpl.
12 366255 Table insert
13 366253 Longitudinal stop cpl.
13A Fence
14 366271 Adjusting knob for incline adjustment
15 366272 Clamping screw for incline
adjustment
16 On/Off switch
17 Motor protection
18 366270 Dust extraction port
19 366275 Sliding stick
22 366268 Saw blade flange
23 366269 Hexagonal screw for saw blade
24 366257 Guide section for longitudinal stop
25 Clamping lever for longitudinal stop
26 366288 Safety label
27 366282 Additional brace
28 Scale for cross-cut adjustment
29 366283 Slip-on foot
30 366273 Ring wrench size 10/21
31 Ring wrench size 10/13
32 366264 Bench width extension
33 366262 Bench length extension
34 366265 Support for table width extension
35 366263 Support for table length extension

Assembly

Please refer to the attached assembly and
operating instruction sheet.
Tighten all screw connections only hand-tight first.
Place the saw with the table surface facing downwards
onto a suitable work surface.
Place then the table width extensions (32) and the table
length extension (33) onto the table plate (10). Secure the
table width and table length extensions on the table plate.
The supports have different lengths.
Support for table width extensions (34)
Support for table length extensions (35)
Secure at first the table legs (2) together with their
supports on the saw.
Secure then the supports on the table width and table
length extensions.
Secure the braces
The braces have different lengths.
Secure the two long braces
Now secure the two short braces
Mount the push-on bases (29) to the table legs.
Install the additional braces (27).
Firmly tighten all screw connections.
Turn the saw right side up so it stands on the table legs.
Adjust the additional braces (27) so that they touch the ground.
Raise the saw blade (5) with the crank (6) to the highest
position.
Remove the table insert (12).
Loosen the screw (A) and pull out the riving knife (8).
Adjust the distance between saw blade and riving knife
(8). This distance must not exceed 5 mm.
Retighten the screw (A).
Attach the safety guard (7) to the riving knife (8).
Place the safety guard together with the screw (B) in the
recess in the riving knife provided for this and pull the
safety guard up to the stop.
Do not over-tighten the screw connection. The safety
guard must move freely.
Slide the extraction hose (9) on the connection piece of
the safety guard (7) and on the extractor neck (18) on the
housing.
Place the pushstick (19) in its holder.

Preparing for commissioning

To achieve flawless functioning of the machine, please
follow the instructions listed:
Place the saw in a place that fulfils the following conditions:
secured against slipping
−
− free of vibrations
even
−
− free of tripping hazards
− adequate light
(4) and (3) to the table legs.
(4) first to the table legs.
(3).
15