Table des Matières
Publicité
★ Tool operates intermittently
- extension cord damaged -> replace extension cord
- internal wiring defective -> contact dealer/service
station
★ Tool leaves ragged finish or motor labours
- cutting height cut too low -> increase cutting height
- cutting blade blunt -> replace cutting blade
- underside of tool badly clogged -> clean tool
- blade mounted upside down -> mount blade correctly
★ Cutting blade not rotating
- cutting blade obstructed -> clear obstruction
- blade nut/bolt loose -> tighten blade nut/bolt
★ Tool vibrates abnormally
- cutting blade damaged -> replace cutting blade
- blade nut/bolt loose -> tighten blade nut/bolt
ENVIRONMENT
• Do not dispose of electric tools, accessories and
packaging together with household waste material
(only for EU countries)
- in observance of European Directive 2002/96/EC on
waste of electric and electronic equipment and its
implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol @ will remind you of this when the need for
disposing occurs
DECLARATION OF CONFORMITY
• We declare under our sole responsibility that this
product is in conformity with the following standards or
standardized documents: EN 60335, EN 61000,
EN 55014 in accordance with the provisions of the
directives 2006/95/EC, 2004/108/EC, 2006/42/EC,
2000/14/EC
• Technical file at: SKIL Europe BV (PT-SEU/PJE),
4825 BD Breda, NL
Arno van der Kloot
Vice President
Operations & Engineering
SKIL Europe BV, 4825 BD Breda, NL
10.06.2010
NOISE/VIBRATION
• Measured in accordance with EN 60335 the sound
pressure level of this tool is 63 dB(A) and the sound
power level 83 dB(A) (standard deviation: 3 dB),
and the vibration 2.5 m/s² (hand-arm method;
uncertainty K = 1.5 m/s²)
• Measured in accordance with 2000/14/EC (EN/ISO 5349)
the guaranteed sound power level LWA is lower than
86 dB(A) (conformity assessment procedure according
to Annex VI)
Notified body : KEMA, Arnhem, NL
Notified body identification number : 0344
Jan Trommelen
Approval Manager
• The vibration emission level has been measured in
accordance with a standardised test given in EN 60335;
it may be used to compare one tool with another and as
a preliminary assessment of exposure to vibration when
using the tool for the applications mentioned
- using the tool for different applications, or with
different or poorly maintainted accessories, may
significantly increase the exposure level
- the times when the tool is switched off or when it is
running but not actually doing the job, may
significantly reduce the exposure level
! protect yourself against the effects of vibration
by maintaining the tool and its accessories,
keeping your hands warm, and organizing
your work patterns
F
Tondeuse à gazon
INTRODUCTION
• Cet outil est destiné uniquement à la tonte du gazon
chez soi
• Cet outil n'est conçu pour un usage professionnel
• Vérifiez que le conditionnement contient toutes les
pièces présentées dans le schéma 2
• Lorsque des pièces manquent ou sont endommagées,
veuillez contacter votre distributeur
• Instructions de montage 2
- la séquence des numéros apparaissant sur le
schéma correspond à la séquence des étapes à
suivre pour le montage de la tondeuse à gazon
! veillez à ce que les 4 roues A soient montées
comme indiqué
! n'oubliez pas de monter le dispositif
d'immobilisation du câble B avant de monter le
manche central C et le manche supérieur D
! serrez fermement toutes les vis et les écrous
• Lisez attentivement ce manuel d'instruction avant
d'utiliser l'appareil et conservez-le pour pouvoir vous y
référer ultérieurement 4
SPECIFICATIONS TECHNIQUES 1
ELEMENTS DE L'OUTIL 3
A Roue
B Dispositif d'immobilisation du cordon d'alimentation
C Manche central
D Manche supérieur
E Clip du câble
F Interrupteur de sécurité
G Gâchette
H Ecrou papillon de fixation
J Bac collecteur
K Clé
L Poignée de transport
M Fentes de ventilation
N Protection arrière
P Plaque d'identification
10
0710
Publicité
Table des Matières
