Sunrise Medical Jay Lite Manuel De L'utilisateur page 3

e nG LIs H
CaUtIon: Installing a cushion on a wheelchair may affect the centre of
gravity of the wheelchair and may cause the wheelchair to tip
backwards, potentially resulting in injury. always assess for the
potential need for anti-tippers or amputee axle adapter brackets
to be added to the wheelchair to help increase stability.
all Jay cushions are designed to help reduce the incidence of decubitus
ulcers. However, no cushion can completely eliminate sitting pressure or
prevent pressure sores. Jay cushions are not a substitute for good skin care
including; proper diet, cleanliness and regular weight transfers. In addition,
prior to prolonged sitting, any cushion should be tried for a few hours at a
time while a clinician inspects your skin to ensure that red pressure spots are
not developing.
you should regularly check for skin redness.the clinical indicator for tissue
break down is skin redness. If your skin develops redness, discontinue the
use of the cushion immediately and see your doctor or therapist.
avoid sharp objects or exposure to excessive heat or open flame.
Jay LIte CUsHIon By Jay
the Jay Lite is designed with the benefits of skin protection in a
lightweight, comfortable and low-maintenance design.the Jay Lite
incorporates a reticulated foam pad and an olilex foam base with a
microclimatic outer cover.
the Jay Lite helps to provide pressure and shear reduction which may
help reduce the incidence of decubitus ulcers. It is comfortable and
doesn't restrict movement, allowing the user to change positions on the
cushion.
the maximum user weight for this product is 250 lbs (113 kg).
Jay LIte CoMponents
reticulated
foam pad
pelvic
Loading area
fIttInG a pressUre dIstrIBUtInG CUsHIon
select a cushion to match your hip width when in the seated position.
the cushion length should extend to within 1" - 2" (2.5cm - 5cm) from
the back of the knees. place the cushion to the back of the wheelchair
with the material identification tags and pelvic loading area toward the
rear. When fit correctly your hips should be to the back of the chair. your
ischials (sitting bones) should be centered in the pelvic loading area of
the cushion. proper footrest adjustment may enhance sitting comfort and
help lower peak sitting pressures. adjust the footrests so your thighs rest
firmly but comfortably on the cushion.
note: do not use the wheelchair's seat width as a guide in determining the
appropriate cushion width. Improper cushion fit may be detrimental
to the performance of a pressure distributing cushion and its
support of the body.
avoid using the cushion on overly stretched seat upholstery. stretched
upholstery does not provide adequate support for the cushion and
improper positioning may result. replace stretched upholstery or
purchase the Jay adjustable solid seat.
112803
rev. a
avoid using overly stretched backrest upholstery. stretched back
upholstery does not provide adequate support for the body and improper
positioning may result. replace stretched backrest upholstery or purchase
a back support product from sunrise that is appropriate for you. Contact
an authorized supplier for a free demonstration of these products.
easy MaIntenanCe & CLeanInG
Monthly cleaning and regular maintenance may help extend the life of
your cushion. during cleaning, component inspection is recommended.
Check the cover for tears and excessive wear and / or any other
abnormalities.
Check the foam base to ensure foam consistency. Check the pelvic
loading area to ensure reticulated foam consistency.
to clean cover
1. remove the cover from the foam base and turn inside out.
2. Machine wash in warm water and drip or tumble dry on low heat.
no ironing required.
note: do not dry clean covers or use industrial washers and dryers to
clean cover. do not steam autoclave. do not bleach.
to refit cover after washing, fit cover back over foam base. ensure the back
of the cover matches up to the back of the foam base.
note: If utilized in an institutional setting, write the resident's name with
a permanent marker on the content label of the covers. this will
help to ensure the return of the covers after washing.
to clean foam base
remove the cover from the foam base. Wipe lightly with a damp cloth. do
not use soap. do not submerge in water. Wipe off with a clean cloth. Let it
completely air-dry before reassembly.
note: avoid submersion of the foam base in water.
reinstall the cover with the reticulated foam pad over foam base. ensure
Cover the back of the cover matches up to the back of the foam base.
foam
base
reasseMBLInG tHe Jay LIte CUsHIon after CLeanInG
follow cleaning and maintenance instructions as described in "easy
Maintenance and Cleaning" then reassemble as follows.
Insert the foam base into the outer cover. ensure that the zipper is at the
rear of the foam base (the part number tag should be to the rear of the
foam base) where the pelvic loading area is located.
3
Laundry Care symbols
Machine wash in warm water
(60° C)
only non-chlorine bleach,
when needed
drip dry
do not iron
do not dry clean
Jay L Ite