HIKOKI NV 100H Mode D'emploi page 7

GENERAL OPERATIONAL PRECAUTIONS
WARNING
Read all safety warnings, instructions,
illustrations and specifi cations provided
with this power tool.
Failure to follow all instructions listed below may result in
serious injury.
Save all warnings and instructions for future
reference.
1. Operate the power tool safely for correct uses.
Do not use the power tool for uses other than those
specifi ed in this instructions.
2. For safe operation handle the power tool correctly.
Please follow the instructions given in this instruction
manual and correctly handle this tool so as to ensure
safe operation. Never let the tool be use by children or
people who do not know enough to be able to handle it
correctly, or let it be used by people who cannot operate
it correctly.
3. Confi rm the safety of the workshop.
Keep unauthorized people away from the workshop.
Especially children should be kept away.
4. The right parts in the right places.
Do not remove any of the covers or screws. Keep them
in place as they have their functions.
Moreover, because it would be dangerous, never
make modifi cations to the tool or use it after making
modifi cations.
5. Check the tool before using it.
Before using the tool, always check that no parts of it
are broken, that all screws are completely tight, and that
no parts are missing or rusty.
6. Excessive work could cause accidents.
Do not make tools and accessories work beyond their
abilities. Excessive work not only damages the power
tool but also is dangerous in itself.
7. Stop operation immediately if abnormalities are
noticed.
Stop operation if you notice abnormalities, or if the
power tool does not work properly; have the power tool
inspected and serviced.
8. Look after the power tool carefully.
If you drop or knock the power tool against things, the
outer frame may be deformed and cracks or other kinds
of damage may occur, so please handle it with suffi cient
care. Also, do not scratch or engrave signs on the power
tool. Owing to high pressure air inside the tool, cracks in
the surface are dangerous.
Never use the power tool if a crack develops or if air is
escaping from a crack.
9. Take good care for a long life.
Always take good care of the power tool and keep it
clean.
10. Inspection at regular intervals is essential for
safety.
Inspect the power tool at regular intervals so that the
power tool can be operated safety and effi ciently at all
times.
11. Consult an authorized service agent if repair or
parts replacement is necessary.
Ensure that the power tool is serviced by authorized
service agent only, and that only genuine replacement
parts are used.
12. Keep the power tool in a proper place.
When not in use, the power tool should be kept in a
dry place out of the reach of children. Put into the body
about 2cc oil through the hose joint to protect the tool
from rust.
(Original instructions)
13. The exploded assembly drawing on this handling
instructions should be used only for authorized
service center.
14. Hold the tool with a fi rm grasp and be prepared to
manage recoil.
15. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the
power tool or these instructions to operate the
power tool.
Power tools are dangerous in the hands of untrained
users.
16. Do not
Modifi cations may reduce the eff ectiveness of
safety measures and increase the risks to the
operator and/or bystander
17. Maintain power tools and accessories. Check
for misalignment or binding of moving parts,
breakage of parts and any other condition that
may aff ect the power tool's operation. If damaged,
have the power tool repaired before use.
Many accidents are caused by poorly maintained
power tools.
18. Do not overreach. Keep proper footing and
balance at all times.
This enables better control of the power tool in
unexpected situations.
19. Keep
operating a power tool.
Distractions can cause you to lose control.
PRECAUTIONS ON USING NAILER
1. Safe operation through correct usage
This tool was designed for driving nails into wood and
similar materials. Use it for its intended purpose only.
2. Make sure air pressure is within the rated range of
air pressure.
Please make sure that the air pressure is within a range
of 12 bar – 23 bar (170 ~ 320 psi), and that the air which
is used is clean and dry. If the air pressure is greater
than 23 bar (320 psi), the life of the power tool will be
shortened and dangerous conditions could develop.
Tools shall not be connected to pressure which
potentially exceeds 26 bar (370 psi).
3. Never operate the equipment with high-pressure
gases other than compressed air.
Never use carbon dioxide, oxygen or another gas from
pressurized containers under any circumstances.
4. Be careful of ignition and explosions.
Since sparks may fl y during nailing, it is dangerous
to use this tool near lacquer, paint, benzine, thinner,
gasoline, gas, adhesives and similar infl ammable
substances as they may ignite or explode. Under no
circumstances should this tool therefore be used in the
vicinity of such infl ammable material.
5. Always wear eye protection (protective goggles).
not properly hit entering the eye is a threat to sight. Eye
protection can be bought at any hardware store. Always
wear eye protection while operating this tool. Use either
eye protection or a wide vision mask over prescription
glasses.
Employers should always enforce the use of eye
protection equipment.
modify the fastener
children and bystanders
When operating the power tool, always wear
eye protection, and ensure that surrounding
people wear eye protection too.
The possibility of fragments of the wire or
plastic linking the nails or nails that were
English
driving tool.
away while
7