Earlex Spray Station HV3500 Mode D'emploi page 8

TECHNIQUE
SPRAY GUN
FLUID TIPS AND NEEDLES
IMPORTANT: SELECTING PAINT
TROUBLESHOOTING
FLUID TIP AND NEEDLE
NEEDLE SELECTION GUIDELINES
SURFACE AND JOB PREPARATION
TOP TIPS
TURBINE UNIT
Needle fluid tip size
CHANGING THE TIP AND NEEDLE
Small tip
VISCOSITY & THINNING
CLEANING INSTRUCTIONS
AFTER USE
Stain/latex tip
TROUBLESHOOTING
THINNING
PARTS LIST
FLUID TIPS AND NEEDLES
Large tip
FINISHING TIPS
FILLING THE PAINT CONTAINER
SPRAY GUN
NEEDLE SELECTION GUIDELINES
SERVICING OF DOUBLE-INSULATED APPLIANCES
OPERATION
FLUID TIP AND NEEDLE
CHANGING THE TIP AND NEEDLE
YOU MUST ENSURE YOU REPLACE BOTH THE FLUID TIP AND NEEDLE.
STARTING TO SPRAY
TURBINE UNIT
TROUBLESHOOTING
Unscrew air cap ring ( ).
2
G
Remove the air cap ( ).
3
G
Remove the spray direction plate (
TECHNIQUE
AFTER USE
FINISHING TIPS
G
It is recommended that you push the trigger forward to help release the fluid tip (
G
Using the needle and fluid tip tool - pincher end A (
G
Insert the needle and fluid tip tool end B (
TROUBLESHOOTING
FLUID TIPS AND NEEDLES
SERVICING OF DOUBLE-INSULATED APPLIANCES
G
Insert the optional needle and screw into place
G
Insert the corresponding fluid tip and screw into place
G
Reassemble all other parts in reverse order.
TOP TIPS
NEEDLE SELECTION GUIDELINES
G
Ensure the air cap ring ( ) is fully tightened and the fluid tip is pushed into place so that the spray gun needle will shut off. Make sure the spray
2
G
direction plate is free to move. If necessary loosen the Air cap ring (2) slightly.
CLEANING INSTRUCTIONS
NEVER DISPOSE OF PAINTS OR SOLVENTS DOWN THE DRAIN. ALWAYS USE YOUR LOCAL WASTE COLLECTION SITE.
CHANGING THE TIP AND NEEDLE
G G
PARTS LIST
TROUBLESHOOTING
PROBLEM
SPRAY GUN
The paint splatters Paint viscosity is too thick
FINISHING TIPS
An area inside the spray gun has a degree of blockage Clean gun and filter paint in the container.
Gun wasn't correctly cleaned from previous project
FLUID TIP AND NEEDLE
SERVICING OF DOUBLE-INSULATED APPLIANCES
The paint drips or sags on Paint viscosity is low/thin
surface
Paint output too high
TURBINE UNIT
Moving too slowly
Spray Trigger held for too long
Spray Gun too close
AFTER USE
I'm getting too much over- Paint flow too high and spraying too close to the
spray or fogging in the room surface
No paint being released Paint too thick
FLUID TIPS AND NEEDLES
Fluid tip blocked
Pick-up tube blocked
Air hose split
NEEDLE SELECTION GUIDELINES
Grainy paint
Paint container almost empty
CHANGING THE TIP AND NEEDLE
Spray gun at an angle
Air inlet blocked
TROUBLESHOOTING
FINISHING TIPS
Orange Peel: Reduce viscosity. Increase atomization with a smaller fluid tip (5). Spray area may be too cold.
SERVICING OF DOUBLE-INSULATED APPLIANCES
Sags or Runs: Move spray gun faster. Spray lighter coat. Increase atomization.
Wet and Milky: Finish applied too heavy. This condition is prone to trap water within coats. Apply lighter coat.
Blushing: Seal coat applied over solvent-based stain that has not been completely dried.
Rough Surface: Seal coat not sanded enough. Sand smooth and re-coat.
Fish Eyes: Surface is contaminated. Clean surface, sand area and re-coat.
Material sprayed
Acrylics, Synthetics, Polyurethane, Thinner, Lacquers, Fluorescent, Oil-Based Stains
Oil base, Hammer, Oxide, Primer, Air Drying, Enamel, Varnish, Marine Paint, Multi-Color, industrial
Synthetics, Oil, Polyurethane, Aluminum Thicker Lacquers, Water-Based Stains, Shellac
Chlorinated Rubber, Oxide, Zinc Rich Primer, Epoxy, Plastic Additives, Floor Paving Paint, Latex
).
4
) remove the fluid tip (
1
) into the inner tube and unscrew the needle anticlockwise, then pull to release the needle.
1
CAUSE
).
5
).
5
ACTION REQUIRED
Thin as required using appropriate thinner (see thinning instructions).
Clean Gun
Add undiluted paint
Reduce the paint output by adjusting the paint flow adjuster (9)
Increase speed of application
Release Trigger sooner
Increase the distance between the spray gun and the work surface
Reduce paint flow and move further from the surface.
Add thinner
Clean the fluid tip (5)
Clean the gun
Replace air hose (13)
Filter the paint
Refill paint container (12)
Check that the pick-up tube (11) is pointing towards the paint
Check the condition of the filter (14) and clean if necessary
8