Technical Information; Distance To Combustible Material; Assembly; Operation - Nordpeis Quadro Manuel D'installation

of the hole for the flue. Distortions in floors and walls
may influence the height. Place the stove for accurate
position and height of the flue/chimney connection.
We accept no liability for typographical errors and
changes.

2. Technical Information

The stoves from Nordpeis have secondary combustion
and are clean burning. The combustion takes place in
two phases: first the wood burns and then the gases
from the fumes are lit by the hot air. This ensures that
these new stoves have minimal emissions of soot
particles and unburnt gases (such as CO) and are
thus better for the environment. Clean burning stoves
require a small amount of wood in order to obtain a
good heat output. Use exclusively clean and dry wood.
We recommend seasoned hardwood with a maximum
moisture content of 20%.
Material:
Surface treatment door/
doorframe:
Fuel:
Operating range:
Draught system:
Combustion system:
Heating area:
Flue outlet:
Flue:
Possible to connect steel
chimney:
Weight Quadro 1:
Weight Quadro 2:
Weight Quadro 3:
Weight Quadro High Top:

3. Distance to Combustible Material

Ensure that the safety distances are respected
(FIG 1 and 2).
The distance from the front of the stove to furniture
needs to be of at least 1 metre. When connecting
a steel chimney to the top outlet use the security
distances required from the manufacturer.

4. Assembly

The following tools are necessary:
•
4mm and 5 mm Allen Key
•
6mm, 10mm and 13 mm Wrench
10
Cast iron / sheet steel
Heat resistant varnish
Wood logs, 30 cm
6,2 kW
Air vent control
Secondary combustion
(clean burning)
45-120 m²
Top and rear
Inner Ø 150 mm
Yes
104 kg
113 kg
118 kg
14 kg

Operation

FIG 3: Adjustment of the door. Loosen the screws
position the door correctly and fasten the
screws again
FIG 4: The air vent control is adjusted with the lever
placed on the left side of the stove
FIG 5: The Thermotte elements
FIG 6-8: Screws for adjusting the levelling of the stove

Operating Control

When the stove is in position, check that all functions
are easy to manoeuvre and appear satisfactory.
Door
Handle turned outwards
Handle parallel with door
frame
Air vent control (FIG 6)
Forward
Back

Flue Outlet Collar

Quadro is delivered as standard with a top flue outlet
collar. In order to change to a posterior mounted flue
outlet:
FIG 9: Remove the loose top lid
FIG 10: Remove the perforated decoration lid in the
back with a hammer, or a hacksaw
FIG 11: Unscrew the rear sheet steel lid
FIG 12: Unscrew the top collar. The draft diverter will
also losen
FIG 13: Fasten the collar on the posterior flue outlet
FIG 14: Fasten the sheet steel lid and the draft
diverter on the top flue outlet. Put on the top lid

Connection of the Flue

Please be aware when connecting the 150 mm flue to
the smoke dome that the flue is placed inside the flue
outlet collar. Use stove cement in the joints. For the flue
connection to the chimney, follow the recommendations
from the chimney manufacturer.

Fresh air supply

FIG 15-18: The possibility to connect a fresh air
supply ducting set

5. Lighting the Fire for the First Time

When the stove is assembled and all instructions
have been observed, a fire can be lit. Be careful with
touching the stove the first few times it is used as it
may damage the varnish. Take care when inserting
logs into the burn chamber, in order not to damage
the Thermotte plates. Please note that during the first
few firings, the insulations panels within the firebox
will release moisture contained within them from
production. This will slow down the burn rate slightly
GB
Open
Closed
Open
Closed