Packaging Content; Assembly; Dry Vacuum Cleaning; Wet Vacuum Cleaning - EWT AquaVac EXCELL 20S Mode D'emploi

PACKAGING CONTENT

Carefully unpack the contents of the box. Hold the two clamps (16) (B1), which hold the upper section (2) (B1) in its position
and fold them upwards (B2).
Loosen the clamps, remove the upper section (B3), and remove the contents from the tank. Please check the parts using the
overview (B1) to make sure they are complete and that there has been no damage in transport. If any parts are missing or
damaged, then please contact your dealer immediately.

ASSEMBLY

Make sure that the connector is not plugged in. Hold the two clamps, which hold the upper section in its position and fold
them upwards (B2).
Loosen the clamps and lift the upper section up and out (B3).
Turn the tank over so that the upper section is on the bottom. Put the two rear wheels (20) in the side guides on the bottom of
the tank (B4).
EXCELL 20S: Put the four rollers (14) in the guides on the bottom of the tank (B5).
EXCELL 30P: Put the two rear wheels (20) in the side guides on the bottom of the tank (B4). Put the two front rollers (14) in the
guides on the bottom of the tank (B5).
Check that the rollers have been pushed completely into the guides. Insert the foam plastic filter (9) that has been supplied for
wet vacuuming. (see the section called "Wet Vacuuming") Insert the dust bag (10) that has been supplied for dry vacuuming.
(see the section called "Dry Vacuuming") Replace the upper section on the tank (B6).
Hook the clamps into the upper section and let them snap into place by pressing the clamps downwards (B7).
Place the large end of the hose (4) on the front air intake stub (17) on the tank (B8).
Select a nozzle (5, 7, 8, 22, 23) (B1) or the ratchet telescopic tube (6) (B1) and slide it over the suction tube (4) (B1), (B9).
Wet/Dry combination nozzle (5): for vacuuming carpets, smooth surfaces and liquids.
Snap the lever forwards for carpets and deep pile fitted carpeting.
Snap the lever backwards for hard floors and hardwearing short pile fitted carpeting and for vacuuming liquids covering a
large area.
handle section with air-leak slider
Open the air leak slider on the handle to regulate the airflow or to remove articles that are stuck to the nozzle (B16).
After using and cleaning the appliance, store the accessories by attaching them to the corresponding holders on the vacuum
cleaner (B17).

DRY VACUUM CLEANING

ATTENTION! It is absolutely necessary for you to read, understand, and observe the section entitled
!
"Safety Instructions and Warnings".
NOTE:
Never vacuum up hazardous materials. If an incorrect dust bag is used, guarantee becomes void.
Make sure that the appliance is not plugged into the power mains.
Make sure that Plaited filter (11) (B1) is installed over the filter basket (3) (B1) (B10).
Slide the dust bag (10) over the hose connection (B11) in the tank. Press it until it snaps firmly into place (B12). In the process,
make sure that the dust bag is not damaged.
Place the upper section on the tank once again and close the clamps (B5), (B6).
Place the large end of the hose on the front air intake stub (17) on the tank (B7) and screw it in by turning to the right.
Select a nozzle (5, 7, 8, 19) (B1) or the connectable tube (6) (B1) and slide it over the suction tube (4) (B1), (B8).
Make sure that the ON/OFF switch (13) (B1) on the appliance is in the "Off" position (position "0") before you plug the power
plug into the receptacle. Plug the power plug into the receptacle. Switch the motor on (ON/OFF switch in position "I").
When you have finished vacuuming, switch the motor off by putting the ON/OFF switch (13) (B1) into the "OFF" position
(position "0").
Unplug the power plug. Check the dust bag (10) (B1) regularly and change it when it is 2/3 full. The bag is designed such that
only air, and no dust, can pass through the paper.
Therefore a used dust bag may not be reused.
NOTE:
! Don't use the dust bag for vacuuming up objects with sharp edges or wet objects.
34
Vacuuming with the Plaited Filter (11)
When using the plaited filter (11), no dust bag (10) and no foam plastic filter (9) is necessary. Remove them if need be.
Place the plaited filter on the filter basket 3 (B10) from the top. After extended use, it can be cleaned by banging it out or
brushing it out. Empty the container (15) in the garbage bin after vacuuming.

WET VACUUM CLEANING

ATTENTION! It is absolutely necessary for you to read, understand, and observe the section entitled
!
"Safety Instructions and Warnings".
NOTE:
Never vacuum up hazardous materials.
Make sure that the appliance is not plugged into the power mains. Check to make sure that the tank (15) (B1) is free of dust and
dirt. Remove the dust bag (10) (B1) or the plaited filter (11) (B1).
Only leave the foam plastic filter (9) (B9) over the filter basket. Place the upper section on the tank once again and close the
clamps (B5), (B6).
Place the large end of the hose on the front air intake stub (17) on the tank (B8) and screw it in by turning to the right. Select a
nozzle (5, 7, 8, 19) (B1) or the connectable tube (6) (B1) and slide it over the suction tube (4) (B1), (B7).
Make sure that the ON/OFF switch (13) (B1) on the appliance is in the "Off" position (position "0") before you plug the power
plug into the receptacle. Plug the power plug into the receptacle.
Switch the motor on (ON/OFF switch in position "I"). When you have finished wet vacuuming, switch the motor off by putting
the ON/OFF switch (13) (B1) into the „OFF" position (position „0").Unplug the power plug.
After use, empty and dry the tank (15) (B1).
Tips: If you want to vacuum up a large quantity of liquid from a sink or a tank, please don't put the entire suction nozzle in the
liquid; rather leave a little space so that some air can also be drawn in along with the liquid, or use the air-leak slider that is
included on the handle section (18). To do this, connect the suction tube (4) and leave the air-leak slider open.
The appliance is equipped with a float switch (12) (B1) that will stop the vacuuming when the tank is full. You will notice that
suction has stopped by the motor now running faster. In this event, switch the appliance off and unplug it.
Be aware that the full tank can be very heavy. In this event, place the appliance over a drain and carefully open the outlet screw.
(18) (B1) (B19).
The contents of the tank can now drain out to a great extent. Now, remove the upper section from the tank (B3) and pour the
rest of the liquid into a suitable tank or drain. Then, you can continue vacuuming after you have replaced the upper section
(B5).
After wet vacuuming, switch off the appliance and unplug it. Empty the container and clean/dry it inside and outside before
putting it away.
Important Information! After wet vacuuming, please proceed as described in the section entitled „Dry Vacuuming" before
you dry vacuum again.

BLOWER FUNCTION

Insert the larger end of the hose in the blower outlet at the back of the motor unit.
Ensure that the On/Off switch is in the Off ("0") position before plugging in (Fig. 1).
Switch on. (Fig. 2)
The hose will now produce a powerful jet of air. This reverse airflow is useful for dislodging objects stuck in the hose. (Fig. 3)
NB:
If the blockage in the hose is not dislodged after a few seconds, switch off and extract it by hand.
GB
35