Usage Instructions; Maintenance And Storage - Hudora 14235 Instructions De Montage Et Mode D'emploi

INSTRUCTIONS ON ASSEMBLY AND USE
EN
INSTRUCTIONS ON ASSEMBLY
No tools are required to assemble the product. The scooter is delivered in its
transport form (folded)! (Picture 1)
Please proceed as follows to get the scooter ready for use
• Pull the lever that is in the direction of movement, located to the right of the folding
mechanism, in order to release the transportation lock. (Picture. 2)
• Unfold the scooter's handlebars upwards.
• Now push the folding hinge towards the handlebar stem until you hear it click
into place. (Picture 3)
• Loosen the quick release fastener on the T-piece of the handlebar shaft by
pushing the lever away from the T-piece. (Picture. 4). Insert the handlebar
grips in the T-piece of the handlebar grip. Use your thumbs to press down
both locking buttons until the the grips can be easily pushed into the T-section.
Turn the handlebar grips until the locking buttons are positioned in the two
openings intended for them and you hear them click into place. Check that
both handlebar grips are fitted correctly by pulling both outwards. Do not let
the two hand grips move out of their locking mechanism, once they are fitted
properly. Now close the quick release fastener on the T-piece of the handlebar
shaft, by inserting the lever into the T-piece. In case the grips are not firmly
fitted enough, open the quick release fastener again and turn the screw on the
opposite side deeper into the thread, so that the fastening clamp tightly sits on
the T-piece.
• Loosen the quick release lock on the handlebar rod by pushing the lever of the quick
release lock until the lever is parallel to the handlebar grip. (Picture 5)
• The handlebars can be locked into place at 4 different heights. Pull the hand-
lebar rod out of the handlebar stem until it is at the required height and the
relevant button has snapped into place. (Picture 6) The maximum height can-
not be exceeded due to the integrated lock.
• Now close the quick release lock by pushing the lever down to the handlebar
stem. (Picture 5)
• In the event that the handlebar does not sit tight enough at the selected height,
open the quick release fastener again and turn the screw on the opposite side
deeper into the thread, so that the fastening clamp tightly sits on the handle-
bar. Repeat this process until the handlebar can be securely adjusted.
• All parts should always by checked for secure fitting before being used, in
particular the folding mechanism, the steering lock and the wheels.
To get the scooter ready for transport again, please carry out the following
actions
• Loosen the quick release lock by pushing the lever of the quick release lock
away from the handlebar stem. (Picture 5)
• Please press the locking button so that the handlebar rod can be moved. (Pic-
ture 6)
• Push the handlebar rod as far as it will go into the handlebar stem.
• Close the quick release lock by pushing the lever down to the handlebar stem.
(Picture 5)
• Loosen the quick release fastener on the T-piece of the handlebar shaft by
pushing the lever away from the T-piece.
• Use your thumbs to press both locking buttons in the handlebar grips and pull the
handlebar grips outwards until they are released completely from the T-sec-
tion. (Picture 4)
• Press the handlebar grips far down until they are parallel to the handlebar
shaft and can be pressed it into the appropriate supports.
• Now close the quick release fastener on the T-piece of the handlebar shaft, by
placing the lever around the T-piece.
• Pull the lever that is in the direction of movement, located to the right of the
folding mechanism, in order to release the assembly lock. (Picture. 2)
• Fold up the scooter by moving the handlebar rod towards the back wheel until
you hear the transport lock click into place. (Picture. 1)
All images are examples of the design.

USAGE INSTRUCTIONS

Nothing's easy at first ...
... most accidents happen to "beginners" within the first ten minutes. Particular
care should be taken during this stage.
Usage instructions
The scooter moves when a foot is used to regularly push off, just as with well-
known children's scooters. Braking is no problem either - simply step on the
friction brake over the back wheel (mudguard).
We recommend folding the scooter by hand after each use or using the stand.
The side stands are in the direction of movement, located on the left hand side
under the running board. Their use is ensured through simply folding and unfol-
ding.
Aluminium is a good and light material but should also be handled carefully as it
is not as hard as steel, for example.

MAINTENANCE AND STORAGE

Use a dry or damp cloth only to clean the product; do not use special cleaning
agents! Check the product for damage or traces of wear and tear before and after
each use. Do not make any structural changes. For your own safety, please use
original spare parts only. These can be sourced from HUDORA. If parts become
damaged or if sharp edges or corners should develop, the product may not be
used any more. If in any doubt, please contact our service team (http://www.
hudora.de/). Store the product in a safe place where it is protected from the
elements, cannot be damaged, and cannot injure anyone.
Replace damaged or worn assembly parts in order to ensure the safety of your
scooter.
WHEEL CHANGE
Replacement wheels are available as accessories from http://www.hudora.
de/service/ and should be replaced when they are worn down. To change the
wheels, loosen the axle fitting with two Allen keys and take the wheels off the
axle. A screwdriver or Allen key can be used to push the bearings out of the wheel
to use them in the new wheel. However, it is usually advisable to change the
bearings when the wheels are changed. Put the bearings into the new wheel with
the bolt spacer and mount them to the frame with the axle screws. Make sure the
axle has been screwed on tightly before starting again!
Bearings
Your scooter is equipped with precision ball bearings which were filled with lubri-
cation at high pressure during manufacture. For this reason, the wheels only run
easily and quickly when there is a load on the scooter. The bearings are mainte-
nance free. If a bearing should fail, it should be replaced completely. Bearings are
available as accessories from http://www.hudora.de/service/
DISPOSAL ADvICE
At the end of the product's life, please dispose of it at an appropriate collection
point in your area. Local waste management companies will be able to answer
your questions on this.
SERvICE
We make every effort to deliver faultless products. If faults do arise however, we
put just as much effort into rectifying them. Therefore, you can find numerous
information on the product, replacement parts, solutions to problems and lost
assembly manuals at http://www.hudora.de/service/
SPARE PARTS AND ORIGINAL ACCESSORIES
AvAILABLE AT: www.hudora.de/service/
5/12