JB Systems Light LED QUADRO-PANEL Mode D'emploi page 4

ENGLISH
HOW TO SET UP THE UNIT
CONTROL PANEL + CONNECTIONS:
1. DISPLAY shows the various menus and the selected functions.
2. LEDS
DMX On
MASTER On
SLAVE On
SOUND Flashing
3. BUTTONS
MENU To select the programming functions
DOWN To go backward in the selected functions
UP To go forward in the selected functions
ENTER To confirm the selected functions
4. DMX INPUT/OUTPUT: used for DMX512 linking. Use good quality 3pin XLR M/F balanced cable to link
the units together.
5. WIRELESS REMOTE CONTROL INPUT: Used to connect RF-8 wireless controller while the unit is used
in standalone or master/slave mode.
6. MAINS INPUT: with IEC socket and integrated fuse holder, connect the supplied mains cable here.
7. MAINS OUTPUT with IEC socket: you can use a special IEC power cable to connect this output with
the mains input of the next LED QUADRO PANEL for easier linking. (max 40 units can be linked)
MAIN MENU:
 To select any of the functions, press the MENU button up to when the required one is shown on the
display or use the DOWN and UP buttons to browse the menu.
 Select the function with the ENTER button (the display blinks).
 Use DOWN and UP buttons to change the mode.
 Once the required mode is selected, press the ENTER button to confirm.
To go back to the main menu without any change press the MENU button shortly. The main menu is shown
in the chart.
DMX Address
Used to set the starting address in a DMX setup.
 Press the MENU button until "Addr" is shown on the display.
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP buttons to change the DMX512 address.
 Once the correct address shows on the display, press the ENTER button to save it.
To go back to the main menu without any change press the MENU button shortly.
If you want to go back to normal running mode: press the MENU button for about 2 seconds.
Channel mode
Used to set the desired channel setup mode.
 Press the MENU button until "ChMd" is shown on the display.
 Press the ENTER button, the display starts blinking.
JB SYSTEMS
®
OPERATION MANUAL
DMX input present
Master mode
Slave mode
Sound activation
3/65 LED QUADRO PANEL
ENGLISH
 Use DOWN and UP buttons to choose 1ch, 4ch, 16ch or
the special 2MSL mode.
 Once the desired channel setup mode shows on the
display, press the ENTER button to save it.
To go back to the main menu without any change press the
MENU button shortly.
If you want to go back to normal running mode: press the
MENU button for about 2 seconds.
Setup/show Mode
Used to choose the right setup mode while used in
standalone or master/slave mode.
Choosing the right setup mode depends on the number of
panels installed:
 Press the MENU button until "Set" is showing on the
display.
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP buttons to select one of the available
setup modes:
 1-1: select this mode when only 1 panel is used or if
you want all panels to show exactly the same
patterns.
 2-2: select this mode when 4 panels are used in a
2x2 matrix setup.
 4-4: select this mode when 16 panels are used in a
4x4 matrix setup.
 Once the right mode shows on the display, press the
ENTER button to save it.
 For each setup mode you can choose from 12 adapted
shows (Sh1 to Sh12) + a random show (Sh0): use the
DOWN and UP buttons to select one of the shows and
confirm with <ENTER>
To go back to the main menu without any change press the
MENU button shortly.
If you want to go back to normal running mode: press the
MENU button for about 2 seconds.
Color Mode
Used to choose one of 32 pre-programmed colors while
used in standalone or master/slave mode. The color of
the complete panel changes.
 Press the MENU button until "CoLo" is shown on the
display.
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP buttons to select 1 of the 32 colors.
 Press the ENTER button to save the selected color.
To go back to the main menu without any change press the
MENU button shortly.
If you want to go back to normal running mode: press the
MENU button for about 2 seconds.
Sound State
The unit works to rhythm of the beat when used in
standalone or master/slave mode
 Press the MENU button until "SOUn" is shown on the display.
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP button to select "On" or "Off" mode.
 Once the mode is selected, press the ENTER button save it.
To go back to the main menu without any change press the MENU button shortly.
If you want to go back to normal running mode: press the MENU button for about 2 seconds.
JB SYSTEMS
®
OPERATION MANUAL
4/65 LED QUADRO PANEL