Fontanot genius_ra 010 Instructions De Montage page 10

Assemble the 116022, 116012 and 033150 elements of the final support with items 011062, 009047 and
005044 according to the depth chosen previously (see point 3) (fig. 4) (fig. 6) (fig. 7).
7. If necessary, cut the final straight tread with an electric jigsaw (cutting is necessary for depths of 29 and
26.5 cm (fig. 4), use sandpaper to remove any roughness on edges and protect with the supplied wood paint
8. Use screws 002040 to fit parts 033142 / BF1 onto straight treads at a distance equal to the going
calculated earlier (see point 3) (fig. 1) (fig. 2).
9. Insert parts 001010 / 001013 into treads (fig. 1) (fig. 2).
10. Determine drilling position on ceiling in position of slots in support plate 116022. Drill with an 18 mm bit (fig. 4).
11. Fix final support to ceiling with parts 008020, without tightening. Fit final tread to support. Check that tread
is horizontal and definitively tighten parts 008020 (fig. 5).
12. Fit part 132013 to cover the plate (fig. 5).
13. Rest intermediate support 116002 / 116004 on final support 116012, inserting spacers 031078 calculated
earlier, and secure with a self-locking wrench. Fit bolt 003039, components 009041, 023039, 009040 and
005040. Fit components 009012 and 011038 to tread without tightening; temporarily insert two balusters
of the railing between one tread and the other to check the exact alignment of the assembly; check that the
tread is horizontal and the balusters vertical, definitively tighten nut 005040 with a torque of 100 Nm, and
parts 009012 and 011038. Prop up the supports as assembly of the structure and treads progresses, so
that the weight does not act on the ceiling. It is essential to insert a prop for every 4-5 supports, and it is
severely prohibited, for safety reasons, to climb onto the staircase before it has been fixed to the floor and
firmly secured. Continue with assembly of the remaining intermediate supports (fig. 1) (fig. 2).
Assembly of landing structure (go to point 15 for models without landing)
14. Fit the 116010 support to the 116002/116004 intermediate support, inserting spacers 031078 as
calculated earlier and without definitively tightening the components. Fit the 116024 elements to the landing
structure 116020 / 116018 / 116016 / 116014 in the position given by the distance from the wall (three
positions are possible). Fit the landing structure to the 116010 support with items 116026 and 011065,
supporting the structure with a sufficient number of props. Fit the item 116008 to the landing structure with
items 116026 and 011065. Position the wooden landing, without fixing it, and check that it is horizontal and
aligned with the staircase. Fit the 116002 intermediate support, inserting 031078 spacers as calculated
earlier, and then the straight tread, using the posts to guarantee that the structure is aligned. Tighten
articles 003039 applying a torque of 100Nm. Take down the landing and fit articles 047083 and 011057,
respecting the upper support surface, drilling the structure with a 5 mm bit and cutting an M6 thread. Trace
the hole centres according to plates 116024, drill the wall with an 18 mm bit, and enlarge the hole entrance
to a diameter of 19mm and a depth of 15 mm to hold the 006001 tightening nut. Fit parts 006001 to the
046029 stays, without reaching the ends, then fix them to the wall with chemical resin (not supplied), wait
until dry, and definitively tighten parts 006001; cover with caps 031083/ 031021/ 031023/ 031044.
Position wooden landing and fix with screws 002040. Continue with assembly of remaining intermediate
supports (fig. 10).
Assembly of 010 railing (go to point 25 for model 020)
15. Finally, fit the 116006 support base, complete with tread, inserting spacers 031078 calculated earlier
without definitively tightening component 003039 and without drilling holes in the floor (fig. 1).
16. Fit items 034041 and 002050 in the respective holes in the balusters. Fit components 033190, 033078,
001027, 001028 to the 127010 staircase balusters (116 cm high) and to the balusters of any item 127014
(91 cm) high positioning items 033190 with items 034041 (fig. 1) (fig. 14).
17. If necessary, cut the lower part of the 127010 balusters to obtain a railing height of about 100 cm. Insert
the 127010 balusters to connect the treads, starting from the top, on the side where the railing is needed.
Position the balusters with article 033078, with the holed part facing upwards. Tighten components 001010,
taking care that that they are vertical (fig.1).
18. Cut a piece of baluster 127012 to the correct length (116 cm high, without holes) to obtain spacers to
connect treads. Insert lateral connection spacers and secure them with components 001010 at the top and
with part 001004 in part 033142 on the lower side (fig.1).
19. Check that the entire staircase is vertical and trace on the floor the centre of the holes in the plate of base
support 116006. Remove the first and second treads and drill floor with a 14 mm bit; insert parts 008021
and definitively tighten. Replace treads removed earlier (fig. 1). If necessary, cut the 1st post and fix it to the
floor with items 011053, 033142 and 008004.
20. Fix the staircase to the wall using components 033010 and items 008004, 011053 and 033056 (drill with
an 8 mm bit) (fig. 10).
21. Cut sections of handrail 140010 to length; assemble with part 046011. For optimal fixing, the handrail must
follow about 1/8 of a turn from the contact point.
10 - Genius 010 - 020 RA