Tool Change - stayer LP1000E BRUSHLESS Instructions D'emploi

gb
4_OPERATING INSTRUCTIONS
OPERATION
Make sure that the power circuit voltage is the same
as that shown on the specification plata of the machina
and that switch is befare connecting the tool to the
power circuit.
Switching the machine on and off
To switch ON:
Grasping the column with the left hand and the handle
with the right hand, tighten the switch. Prepare to
counter the starting torque when the appliance is
switched on. LP710E: it is possible to keep the switch
locked by pressing the button to the right of the ON /
OFF button.
In the LP1000E model, if you quickly press twice
in succession, you can enter protection due to
the unintentional start of the machine. In these
conditions the machine will stop and you will have to
wait a few seconds for safety before restarting them.
To start correctly, always keep the power switch
pressed.
To switch OFF:
In the LP1000E model, if you quickly press twice
in succession, you can enter protection due to the
unintentional start of the machine. In these conditions
the machine will stop and you will have to wait a few
seconds for safety before restarting them. To start
correctly, always keep the power switch pressed.
LP1000E: basta premere l'interruttore per spegnere la
macchina.
LP710E: Interrompere la pressione del pulsante prin-
cipale o, se la macchina è bloccata, premere breve-
mente il pulsante principale.
Press the rocker switch to the. After the machina has
been switched off, the sanding disc will still rotate far
a rime. Take care that parts of your body do not come
into contact with the disc and do not set the machina
down while it is still rotating!

TOOL CHANGE

Change of the disk
The abrasive disk can be easily changed thanks to the
fabric adhesion system (Velcro). Just pull the disc and
replace it with a new one.
NOTE: Only use sandpaper discs which fit properly
and which are designad far vacuum use.
Change of brush ring
The brush bristles on the edge of the sanding
plata cover serve two purposes, they keep the
sanding disc properly aligned with the work surface
without gouging and they also help the efficiency
of the dust collection by the vacuum cleaner.
These brush bristles will wear with continuad use.
The sanding plata cover should be replaced when the
bristles are too worn to ensure effective dust collection
and stabilization of the sanding head.
Replacement is the opposite of removal. Entrust all
repairs to an authorized service centre.
Remove the brush ring by removing the 6 or 8-star
screws.
ADJUSTING OPERATION
Adjustment of the rotation speed
The speed of the machine is variable to suit different
tasks. lt can be adjusted from 1000 min·1 up to 2000
min·1 by using the thumb wheel. Turn in the counter
clockwise direction to increase the speed and in the
clockwise direction to decrease the speed. Generally,
you should use the higher speed far fast stock removal
and the lower speed far more precise control.
5_INSTRUCTIONS OF USE
Come usare questo apparecchio
Effective control of this powerful tool requires two-
handed tor maximum safety and control.
Always wear respiratory mask and glasses with EPI
level.
Once the machi ne and vacuum cleaner are set up
and all safety measures and equipment are in place,
begin by turning on the vacuum cleaner and then the
machine. (lf you are using a vacuum cleaner with
integrated switching, then simply turn the machine on.)
Begin sanding and carefully contact the work surface
as lightly as possible-just enough to keep the sanding
head flat against the surface.
The joist in the sanding head allows the sanding disc
to follow the contours of the work surface.
The best technique is to use overlapping sweeps and
keep the head in constant motion. Never stop too long
in any one place ar there will be swirl marks. With
experience it will be very easy to create excellent
results.
For a better job in the joints between walls and / or
ceilings in the LP1000E model, a part of the brush ring
can be removed to gain access to the 100% joint. To
remove, release the tab on the top of the sanding head
to remove the part.
- 12 -