Maintenance; General; Daily Cleaning; Cleaning The Toast Feed Ramp - Hatco Toast Qwik TQ-10 Série Manuel D'installation Et D'utilisation

English

General

Hatco Toast-Qwik Electric Conveyor Toasters are designed for
®
maximum durability and

maintenance.

WARNING
ELECTRIC SHOCK HAzARD:
• Turn OFF power switch, unplug power cord, and allow
unit to cool before performing maintenance, cleaning,
setup, or attempting to clear a jam.
• DO NOT submerge or saturate with water. Unit is not
waterproof. Do not operate if unit has been submerged
or saturated with water.
• Do not steam clean or use excessive water on unit.
• This unit is not "jet-proof" construction. Do not use jet-
clean spray to clean this unit.
• Do not clean unit when it is energized or hot.
• Do not allow liquids to spill into unit.
• This unit must be serviced by qualified personnel only.
Service by unqualified personnel may lead to electric
shock or burn.
• Use only Genuine Hatco Replacement Parts when
service is required. Failure to use Genuine Hatco
Replacement Parts will void all warranties and may
subject operators of the equipment to hazardous
electrical voltage, resulting in electrical shock or burn.
Genuine Hatco Replacement Parts are specified to
operate safely in the environments in which they are
used. Some aftermarket or generic replacement parts
do not have the characteristics that will allow them to
operate safely in Hatco equipment.
This unit has no "user-serviceable" parts. If service is
required on this unit, contact an Authorized Hatco Service
Agent or contact the Hatco Service Department at
800-558-0607 or 414-671-6350; fax 800-690-2966; or
International fax 414-671-3976.

Daily Cleaning

To preserve the finish of the unit, it is recommended that the metal
surfaces be wiped daily with a damp cloth.
WARNING
Submerging or saturating unit with water will damage the
unit and void unit warranty.
NOTICE
Use non-abrasive cleaners and cloths only. Abrasive
cleaners and cloths could scratch finish of unit, marring its
appearance and making it susceptible to soil accumulation.
Clean unit daily to avoid malfunctions and maintain
sanitary operation.
1. Turn off the unit, unplug the power cord, and allow the unit
to cool.
2. Remove and empty the crumb tray and the toast collector
pan.
a. Wash the crumb tray and the toast collector pan with
warm water and a mild detergent. Rinse with water.
b. allow the crumb tray and toast collector pan to air dry, or
dry with a soft cloth.
Form No. TQ2m-0414
performance with minimum
BURN HAzARD: Do not remove crumb tray for cleaning
until toaster is cool.
3. Wipe the exterior surfaces of the toaster with a non-
abrasive, damp cloth.
4. Stubborn stains may be removed with a good stainless
steel cleaner or a non-abrasive cleaner. Hard to reach
areas should be cleaned with a small brush and mild soap.
NOTE: The conveyor gear motor and conveyor system are
permanently lubricated and require no lubrication.
5. Check the cooling fan vents and clean any debris
NOTE: TQ-400, -800, -1200, and -1800 series toasters are
equipped with a cooling fan directly below the control
panel area. Check/clean the cooling fan vents monthly
or anytime the Warning light illuminates. For excessive
buildup, use a vacuum cleaner to clear the vents.
Clogged vents will cause the toaster to overheat and
shut down.
Cooling Fan
Vents
Cooling Fan Vents (TQ-400 shown)
6. Reinstall the crumb tray and toast collector pan. Refer to
the INSTaLLaTION section for instructions.

Cleaning the Toast Feed Ramp

1. Remove the toast feed ramp by pressing in the two wire
spokes and lifting.
2. Wipe clean with a non-abrasive, damp cloth or soak the
ramp in a mild solution of 1 cup (227 mL) ammonia and
1 gallon (3.785 L) of water.
3. Reinstall the toast feed ramp by aligning the wire spokes
with the holes in the toaster.

Cleaning the Bottom Element Reflector

The bottom heating element reflector inside the toasting
chamber has slots that allow bread crumbs to drop through to
the crumb tray. Over an extended period of use, bread crumbs
may build up on the reflector and not drop through onto the tray.
1. Turn off the unit, unplug the power cord, and allow the unit
to cool.
2. Wipe the crumbs onto the crumb tray using a bristle brush.
• To wipe the reflector, place the bristle brush through the
conveyor belt and wipe to each side.
3. Perform the "Daily Cleaning" procedure in this section.
15
MAINTENANCE
CAUTION
Warning
Light