Overhead Rigging - JB Systems Light LED BALL INDOOR Mode D'emploi

ENGLISH
Follow the these steps (in this example the start address is set to 403):
• Make sure the DMX cables of all units are connected.
• Connect all units to the mains so they are switched on.
• Edit scene1: CH1= 0, CH2= 255, CH3= 1, CH4= 146
• Edit scene2: CH1= 255, CH2= 0, CH3= 1, CH4= 146
• Program these 2 scenes in a chase and run it to automatically set the DMX addresses.
You will notice that all units flash 1x to indicate that the addresses are set.
• Press the blackout button on your controller 2times to set all units in blackout and back on.
• Done: in this case the first unit has start address 403, the 2
address 411, ...
Remark: you can mix the units with other DMX-effects that don't have the remote DMX-addressing
option. In that case you still have to set the DMX-addresses of these DMX-effects manually!

OVERHEAD RIGGING

• Important: The installation must be carried out by qualified service personal only. Improper
installation can result in serious injuries and/or damage to property. Overhead rigging requires
extensive experience! Working load limits should be respected, certified installation materials
should be used, the installed device should be inspected regularly for safety.
• Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging
and servicing.
• The device should be installed out of reach of people and outside areas where persons may walk by or be
seated.
• Before rigging make sure that the installation area can hold a minimum point load of 10times the device's
weight.
• Always use a certified safety cable that can hold 12times the weight of the device when installing the unit.
This secondary safety attachment should be installed in a way that no part of the installation can drop
more than 20cm if the main attachment fails.
• The device should be well fixed.
• The operator has to make sure that the safety-relating and machine-technical installations are approved by
an expert before using them for the first time. The installations should be inspected every year by a skilled
person to be sure that safety is still optimal.
• 3 different fixing methods are possible:
• Fixed to ceiling or truss (1m chain included)
• Wall fixing (optional wall adapter available)
• Pole mount (optional adapter for poles up to D=60mm available)
JB SYSTEMS®
OPERATION MANUAL
nd
has address 407, the 3
5/35 LED BALL INDOOR
ENGLISH
OPERATING INSTRUCTIONS
A. Standalone 1unit:
• Just connect the unit to the mains and put on some music. The unit will start working automatically to
the rhythm of the music.
Remark: You can connect a CA-8 remote controller to the unit if you want to have more control.
B. Two or more units in master/slave setup:
• Connect 2 to maximum 16 units together. Refer to the chapter "electrical installation" to learn how to
do this (don't forget to address all units properly!)
rd
has
• Connect all units to the mains and put on some music. The units will start working automatically to the
rhythm of the music and show the internal chase programs.
Remark: You can connect a CA-8 remote controller to the master unit if you want to have more control
over the master/slave operation.
C. Connect the optional CA-8 controller for more control:
The CA-8 controller can only be used in standalone or master/slave mode. Connect the controller to the
CA-8 input of the first unit (master). Now you can control all the connected units:
BUTTON
STANDBY
FUNCTION
MODE
D. Controlled by universal DMX-controller:
• Connect all units together. Refer
to the
installation for two or more units in
DMX-mode" to learn how to do
this (don't forget to address all
units properly!)
• Connect all units to the mains and
turn on the DMX controller.
Since each unit has its own DMX-
address, you can control them
individually. Remember that each
unit uses 4 DMX-channels as shown
in the DMX chart.
JB SYSTEMS®
ACTIONS
To blackout all the fixtures
Strobe 9 Color select Color Chase
1.Synchronous strobe White Red 1. The same color
in white color Orange Yellow 2. Different color
2.The same color Green Cyan 3. One light chase
chase Blue Purple 4. Two lights chase
3.Different color Magenta 5. Four lights chase
strobe
Sound 1 Manual Sound 2
(LED OFF) (LED ON) (LED slow blinking)
chapter "Electrical
6/35
OPERATION MANUAL
Color Fade
1. Fast speed
2. Middle speed
3. Slow speed
Auto
(LED fast blinking)
LED BALL INDOOR