Velocity Curve - Korg Grandstage 73 Manuel D'utilisation

The default setting is "1".
Download and refer to the "Grandstage 88/73 MIDI Guide" (PDF)
for details.
MIDI Ch Mode (MIDI channel mode)
This selects the MIDI channel mode used by the Grandstage to
transmit and receive MIDI data.
Global Only: Uses only the channels set in "MIDI Channel".
When playing in layered or split mode, this keyboard will
transmit and receive on only one channel.
U/L Individual (Upper/Lower Individual): the channels set
using the "MIDI Channel" and "MIDI Ch (Lower)" settings will
be used to transmit and receive MIDI data for the KEYBOARDS
and ENSEMBLE sections.
The default setting is "Global Only".
Download and refer to the "Grandstage 88/73 MIDI Guide" (PDF)
for details.
MIDI Ch (Lower) (MIDI channel for the lower part)
This setting is enabled when the MIDI Ch Mode is set to
"U/L Individual". This specifies the MIDI channels on which the
Grandstage will transmit and receive (from 1–16) on the lower
ENSEMBLE section note range.
The default setting is "2".
Download and refer to the "Grandstage 88/73 MIDI Guide" (PDF)
for details.
Local Control (MIDI local control)
Set whether the Grandstage's own keyboard, wheels and other
controls will control the Grandstage's sound engine (On), or
whether the Grandstage's own keyboard will only be used to
output MIDI messages to external devices, without controlling
the Grandstage's sound engine (Off). Normally, this is "On"
when playing the Grandstage by itself.
The default setting is "On".
Download and refer to the "Grandstage 88/73 MIDI Guide" (PDF)
for details.

Velocity Curve

This sets how the volume and tone will be changed in response
to the keyboard velocity (how hard the keys are played) on the
Grandstage.
The default setting is "4 (Normal)".
127
1
Soft
Value Details
1 (Heavy), 2, 3 These curves produce an effect when you play
strongly.
4 (Normal) This is the typical curve.
5, 6 These curves let you produce dynamic change
without having to play very hard.
7 This curve provides a flat effect when playing
softly.
8 (Light) This curve provides an even more flat effect
when playing softly.
9 (Wide) This curve produces an even softer response
when playing softly compared to the typical
curve #4.
16
6
5
7
8
4
3
2
1
9
Strong
Convert Position
This specifies the position at which the transposition and velocity
curve will apply. The setting has an effect on MIDI data that is
transmitted and received.
Note:
The transpose value is set from the TRANSPOSE button
(see page 11).
Pre-MIDI: Transposes and applies the velocity curve to data
immediately after it is outputted from the keyboard.
Post-MIDI: Transposes and applies the velocity curve to data
before it enters the sound generator.
This setting does not have an effect when playing the
Grandstage's own sounds using this keyboard.
The default setting is "Pre-MIDI".
Download and refer to the "Grandstage 88/73 MIDI Guide" (PDF)
for details.
Auto Power Off
When a set period of time has passed without playing the keys,
turning the knobs or pressing the buttons on this keyboard, the
power is automatically turned off. This is called "auto power off".
Select a setting of either "Disabled" or "4 Hours".
The default setting is "4 Hours", which means that the power
will automatically turn off if the Grandstage is not used for four
hours.
Brightness (display brightness)
Sets the display brightness for each display corresponding to the
two sections on the front panel. The setting range is from 1–10,
and the default setting is "8".
Continuing to use the Grandstage while the brightness is set
to a high value will have an effect on the life of the displays.
KORG Logo Light (turning the KORG logo light on/off)
This sets the brightness of the rear panel KORG logo. To make
the logo light up in response to the note-on velocities played on
the keyboard, set this to "On-Note Vel".
The default setting is "5".
KORG Logo Color (color of KORG light)
Sets the color of the KORG logo on the rear panel when it lights
up.
The logo will light up in one of the following colors: white, red,
pink, blue, green, purple, or gold.
When selecting "Cycle", the color will change gradually over time.
The default setting is "White".
Foot - Pedal (foot pedal functions)
This sets the functions that will be controlled when a foot pedal
(such as the XVP-20, XVP-10 or EXP-2, sold separately) is
connected to the FOOT CONTROLLERS PEDAL jack on the
rear panel. This allows the volume and effects to be controlled.
The default setting is "Expression (CC#11)".
Function Details
Off The connected pedal will not function.
Expression The pedal will control expression. Controls
(CC#11) the volume on the output line for both the
KEYBOARDS and ENSEMBLE sections. The value
of the MIDI Volume (CC#7) message and the
expression are multiplied to get the actual
volume. (*1) (*2)
Pedal Wah
This functions differently from normal in some
programs. For programs that include the words
"Pedal Wah", the pedal controls the pedal wah
effect within the program, not the volume.