Wolfcraft MASTER cut 2600 Traduction De La Notice D'utilisation Originale page 45

SAFETY INFORMATION FOR OPERATING CIRCULAR BENCH SAWS
• Switch off the bench saw and disconnect it from the mains before removing the table insert, changing the saw blade,
adjusting the riving knife or saw blade protective cover and if the machine is going to be left unattended. Precautions help
to avoid accidents.
• Never leave the bench saw running unattended. Switch off the power tool and wait until it has come to a complete stop
before leaving it. An unattended saw is an uncontrolled hazard.
• Install the bench saw in a location that is flat and well lit, where you can stand securely and maintain your balance.
The installation location must offer enough space to handle the size of your workpieces. Piled-up sawdust is flammable and can
ignite spontaneously.
• Remove sawdust and shavings from under the saw table and/or from the dust extractor at regular intervals. Piled-up sawdust
is flammable and can ignite spontaneously.
• Secure the circular bench saw. A circular bench saw that has not been secured properly can move or tip over.
• Remove adjusting tools, wood scraps, etc. from the circular bench saw before switching it on. Distractions or possible jams can
be dangerous.
• Always use saw blades in the correct size and with the appropriate locating hole (e.g. diamond-shaped or round). Saw blades
that are not compatible with the saw's mounting hardware will run off-centre and result in loss of control.
• Never use damaged or the wrong saw blade mounting materials such as flanges, washers, nuts or bolts. This saw blade
mounting material has been designed specifically for your saw, for safe operation and optimum performance.
• Never climb onto the circular bench saw and do not use the circular bench saw as a step stool. Serious injuries can occur if the
power tool tips over or if you accidentally come into contact with the saw blade.
• Make sure that the saw blade is mounted in the correct direction of rotation. Do not use grinding wheels or wire brushes with
the circular bench saw. Improper mounting of the saw blade or using accessories that are not recommended can result in serious
injuries.
Product-specific safety information
• Only use the bench saw with the protective cover properly installed.
• CAUTION! Check whether the blade of the circular saw is mounted parallel to the opening in the gap insert. If necessary,
re-align the circular hand saw.
• Only circular saw blades are allowed as cutting tools.
• Use the correct saw blade for the material to be cut.
• Use only saw blades with a diameter that matches the specifications on the circular hand saw used.
• Use only saw blades that are rated with an equal or higher speed than the speed of the power tool.
• Use only saw blades recommended by the power tool manufacturer and that comply with EN 847-1 if they are to be used to cut wood
or similar materials.
• Keep in mind that it is not permitted to perform complicated concealed cut procedures or to cut bevels/wedges.
• Do not use the tool on materials other than wood or easily machined plastics.
• When cutting wood and plastics, prevent overheating of the saw teeth. Reduce the feed to prevent the plastic from melting.
• When making longitudinal cuts at an angle, do not stand at the side toward which the saw is angled.
• Wear suitable personal protective equipment, hearing protection and goggles.
• Only wear protective gloves when handling saw blades.
SAFETY INFORMATION FOR JIGSAWS
• Apart from these machine-specific safety instructions, also observe the safety instructions for the jigsaw used.
• Never work with a damaged jigsaw.
• Avoid overloading the jigsaw.
• Make sure that you install the gap insert for jigsaws correctly.
• When cutting, make sure that the jigsaw blade always protrudes from the material.
SAFETY INFORMATION FOR MITRE SAWS
• In addition to this tool-specific safety information, make sure you observe the safety information for the mitre saw used.
• Do not work with a damaged mitre saw and do not use blunt or damaged saw blades.
• Support long workpieces on the receiving side to prevent dangerous situations caused by accidental tipping over.
• Mount the mitre saw using the fastening materials supplied in accordance with the instructions in this manual.
t
45