Muting The Sound; Compiling An Individual Title Sequence - Monacor M-30CD Mode D'emploi

5.6 Muting the sound

For muting the sound, press the button MUTE (15) on
the remote control. To switch on the sound again, press
the button MUTE once again.

5.7 Compiling an individual title sequence

For replaying only a few titles from a data carrier in a
certain order, a sequence of 10 titles max. can be pro-
grammed.
1) The CD player must be in the stop mode, press the
button STOP (2), if required.
2) Switch on the programming mode with the button
PROG (16). All other buttons must be pressed within
10 seconds respectively, otherwise the programming
mode will be exited. In this case, press the button
PROG once again. The display will show:
– for a CD without MP3 files
MEM
TR00 P-01 CD
– for a CD with MP3 files
MEM P-01
000 000
3) In case of CDs without MP3 files, skip this operating
step and directly proceed with step 4.
In case of MP3 files, first select the number of the
folder containing the first title desired for the title
sequence. This is also required if all files have been
memorized on the data carrier in the root directory
ROOT without folder. The root directory will then be
named Folder 1.
If there are files in the root directory, the folders in
the root directory starting from Folder No. 2 will be
numbered in ascending alphabetic order. If not, the
numbering for the folders will start with the number 1,
followed by all subfolders and then by any subsub-
folders etc.
Select the folder number with the buttons DOWN/
REV and UP/CUE (3) or enter it with the numerical
keys (12). To memorize, press the button PROG. The
three zeroes below the indication "P-01" will flash as
a request to enter the title number.
4) Select the number of the first title for the title se-
quence with the buttons DOWN/REV and UP/CUE
(3) or enter it with the numerical keys (12). If there are
MP3 files in folders, please note that these files are
not numbered consecutively but that the first file in
each folder is always named No. 1.
All rights reserved by MONACOR
reproduced in any form or by any means for any commercial use.
® INTERNATIONAL GmbH & Co. KG. No part of this instruction manual may be
5) To memorize press the button PROG. The display will
show the next memory location number, e. g. "P-02".
6) Repeat the operating steps (3), 4 and 5 for all further
titles desired until the entire title sequence has been
programmed.
7) To start the title sequence, press the button PLAY/
PAUSE (4). The upper display line will show "MEM"
(memory) and the title sequence will be replayed.
8) With the buttons DOWN/REV and UP/CUE, select
any title of the title sequence or activate the fast for-
ward/reverse function within a title by keeping the
corresponding button pressed.
9) After replaying the title sequence or when pressing the
button STOP, the CD player will go to the stop mode.
To restart the title sequence once again, first press the
button PROG, then the button PLAY/ PAUSE.
Note: A programmed title sequence will be deleted if
the data carrier is changed, if the button STOP is
pressed in the programming mode, and if the CD player
is switched off.
6 Maintenance
Protect the CD player module against dust, vibrations,
direct sunlight, humidity, and heat (admissible ambient
temperature range 0 – 40 °C). For cleaning only use a
soft, dry cloth, by no means water or chemicals.
Note on sound interruptions and reading errors
Cigarette smoke easily penetrates through all openings
of the unit and settles on the optics of the laser system.
This deposit may cause reading errors and sound inter-
ruptions. As cigarette smoke cannot always be avoided
(e. g. in a discothèque), the unit must in this case be
cleaned by authorized personnel. There is a charge on
this cleaning, even during the warranty time!
7 Specifications
Power supply: . . . . . . . . . . . . 12 V , 800 mA
Audio output: . . . . . . . . . . . . . 1 V
Dimensions (W × H × D): . . . 174 × 51.5 × 166 mm
Mounting cutout (W × H × D):. 155 × 49.5 × 156 mm
Weight: . . . . . . . . . . . . . . . . . 1.3 kg
Subject to technical modification.
GB
11