Residual Risks; Technical Data - Scheppach DP16VLS Consignes D'utilisation Et De Sécurité

5. Do not mix old and new batteries or batteries of different
types or manufacturers! Replace an entire set of batteries
at the same time.
6. Immediately remove used
device and dispose
not dispose batteries
Defective or used batteries must be recycled according
to Directive 2006/66 / EC. Give back batteries and /
or the device has been offered to the collective facilities.
About disposal facilities you can inform by your munici-
pal or city government.
7. Do not allow batteries to heat up!
8. Do not weld or solder directly on batteries!
9. Do not dismantle batteries!
10. Do not allow batteries to deform!
11. Do not throw batteries into fire!
12. Keep batteries out of the reach of children.
13. Do not allow children to replace batteries without super-
vision!
14. Do not keep batteries near fire, ovens or other sources of
heat. Do not use batteries in direct sunlight or store them
in vehicles in hot weather.
15. Keep unused batteries in the original packaging and
keep them away from metal objects. Do not mix un-
packed batteries or toss them together! This can lead to
a short-circuit of the battery and thus damage, burns or
even the risk of fire.
16. Remove batteries from the equipment when it will not be
used for an extended period of time, unless it is for emer-
gencies!
17. NEVER handle batteries that have leaked without appro-
priate protection. If the leaked fluid comes into contact
with your skin, the skin in this area should be rinsed off
under running water immediately. Always prevent the
fluid from coming into contact with the eyes and mouth.
In the event of contact, please seek immediate medical
attention.
18. Clean the battery contacts and corresponding contacts in
the device prior to inserting the batteries:

Residual risks

The machine has been built according to the state
of the art and the recognised technical safety re-
quirements. However, individual residual risks can
arise during operation.
• Health hazard due to electrical power, with the use of im-
proper electrical connection cables.
• Furthermore, despite all precautions having been met, some
non-obvious residual risks may still remain.
• Residual risks can be minimised if the „safety instructions"
and the „Proper use" are observed along with the whole of
the operating instructions.
• Do not load the machine unnecessarily: excessive pressure
when sawing will quickly damage the saw blade, which re-
sults in reduced output of the machine in the processing and
in cut precision.
• When cutting plastic material, please always use clamps:
the parts which should be cut must always be fixed between
the clamps.
• Use the tool that is recommended in this manual. In doing so,
your drill press provides optimal performance.
20 GB
batteries from the
of them properly! Do
with household waste.
• Hands may never enter the processing zone when the ma-
chine is in operation.
• Release the handle button and switch off the machine prior
to any operations.

7. Technical data

Nominal input voltage
Power rating
Motor speed
Output speed
Drill chuck mount
Drill chuck
Dimensions of drill table
Angle adjustment of
table
Drill depth
Pillar diameter
Height
Base area
Weight
Laser class
Wavelength of laser
Laser output
*Operating mode S2, short-term operation
Noise and vibration values
The total noise values determined in accordance with EN
61029.
Sound pressure level L
pA
Uncertainty K
pA
Sound power level L
WA
Uncertainty K
WA
Wear hearing protection.
The effects of noise can cause a loss of hearing. Total vibration
values (vector sum - three directions) determined in accordance
with EN 61029.
Vibration emission value a = 1,6 m/s
h
Uncertainty K = 1,5 m/s
2
The specified vibration value was established in accordance
with a standardized testing method. It may change accord-
ing to how the electric equipment is used and may exceed the
specified value in exceptional circumstances.
The specified vibration value can be used to compare the
equipment with other electric power tools.
The specified vibration value can be used for initial assessment
of a harmful effect.
230 V ~ /50 Hz
500 W (S2* 15min)
1450 min
-1
600 min
-1
900 min
-1
1300 min
-1
1800 min
-1
2600 min
-1
B16
3 - 16 mm
160 x 160 mm
45°/0°/45°
50 mm
46 mm
600 mm
290 x 190 mm
14,1 kg
II
650 nm
< 1 mW
71 dB (A)
3 dB
84 dB (A)
3 dB
2