PrimAster BS3000 Traduction De La Notice Originale page 33

11 Secure the workpiece
– Use the clamping devices or a vice to hold the
workpiece in place. In this manner, it is held
more securely than with your hand.
– An additional support is necessary for long
workpieces (table, trestle, etc.) in order to pre-
vent the machine from tipping over.
– Always press the workpiece firmly against
the working plate and stop in order to prevent
bouncing and twisting of the workpiece.
12 Avoid abnormal posture
– Make sure that you have secure footing and
always maintain your balance.
– Avoid awkward hand positions in which a sud-
den slip could cause one or both hands to come
into contact with the saw blade.
13 Take care of your tools
– Keep cutting tools sharp and clean in order to
be able to work better and more safely.
– Follow the instructions for lubrication and for
tool replacement.
– Check the connection cable of the electric tool
regularly and have it replaced by a recognised
specialist when damaged.
– Check extension cables regularly and replace
them when damaged.
– Keep the handle dry, clean and free of oil and
grease.
14 Pull the plug out of the outlet
– Never remove loose splinters, chips or jammed
wood pieces from the running saw blade.
– During non-use of the electric tool or prior to
maintenance and when replacing tools such as
saw blades, bits, milling heads.
– When the saw blade is blocked due to abnormal
feed force during cutting, turn the machine off
and disconnect it from power supply. Remove
the work piece and ensure that the saw blade
runs free. Turn the machine on and start new
cutting operation with reduced feed force.
15 Do not leave a tool key inserted
– Before switching on, make sure that keys and
adjusting tools are removed.
16 Avoid inadvertent starting
– Make sure that the switch is switched off when
plugging the plug into an outlet.
17 Use extension cables for outdoors
– Only use approved and appropriately identified
extension cables for use outdoors.
– Only use cable reels in the unrolled state.
18 Remain attentive
– Pay attention to what you are doing. Remain
sensible when working. Do not use the electric
tool when you are distracted.
19 Check the electric tool for potential damage
– Protective devices and other parts must be
carefully inspected to ensure that they are fault-
free and function as intended prior to continued
use of the electric tool.
– Check whether the moving parts function
faultlessly and do not jam or whether parts are
damaged. All parts must be correctly mounted
and all conditions must be fulfilled to ensure
fault-free operation of the electric tool.
– The moving protective hood may not be fixed
in the open position.
– Damaged protective devices and parts must be
properly repaired or replaced by a recognised
workshop, insofar as nothing different is spe-
cified in the operating manual.
– Damaged switches must be replaced at a cus-
tomer service workshop.
– Do not use any faulty or damaged connection
cables.
– Do not use any electric tool on which the switch
cannot be switched on and off.
20 ATTENTION!
– The use of other insertion tools and other ac-
cessories can entail a risk of injury.
21 Have your electric tool repaired by a qualified
electrician
– This electric tool conforms to the applicable
safety regulations. Repairs may only be perfor-
med by an electrician using original spare parts.
Otherwise accidents can occur.
22 Do not use the cable for purposes for which it is
not intended Do not use the cable to pull the plug
out of the outlet. Protect the cable from heat, oil
and sharp edges.
Mesures de sécurité specifiques pour les scies a
ruban
• Ne pas utiliser l'outil lorsque le protecteur de lame
de scie est ouvert.
• Si la coupe concerne du bois rond ou de forme ir-
régulière, il est indispensable d'utiliser un dispositif
empêchant la pièce de tourner.
• Ne pas utiliser de lames de scie déformées ou en-
dommagées.
• Remplacez la plaquette lumière de table lorsqu'il est
endommagé.
• Raccordez un dispositif d'aspiration de la poussière.
Si des raccords d'aspiration de poussière et des dis-
positifs de collecte sont disponibles, assurez-vous
que ceux-ci sont raccordés et utilisés, notamment
lorsque vous coupez du bois.
• N'utilisez la scie à ruban que si l'ensemble des sys-
tèmes de protections sont mis en place
• Utilisez l'outil approprié. N'utilisez pas de machine
de faible puissance pour les travaux lourds. N'utilisez
pas les outils à des fins pour lesquelles ils ne sont
pas conçus. N'employez pas une scie à ruban par
exemple pour découper des branches ou du bois de
chauffage. Faites attention : l'utilisation de la scie à
ruban et la vitesse à utiliser dépendent du type de
matériau à couper
• Ne pas nettoyer la scie à ruban pendant l'utilisation.
• Utilisez des équipements de protection individuelle:
- Portez un casque de protection auditif.
- Utilisez un masque de protection ou masque
anti poussière.
FR 33