Technical Specifications - Hudora 76914 Instructions De Montage Et Mode D'emploi

INSTRUCTIONS ON ASSEMBLY AND USE
EN
CONGRATULATIONS ON PURCHASING YOUR PRODUCT!
Please read these instructions carefully. The instructions are an integral compo-
nent of the product. Therefore, please store them and the packaging carefully in
case questions arise in the future. Please always include these instructions when
giving the product to a third party. This product must be assembled by an adult.
This product is not designed for industrial use. The use of the product requires
certain capabilities and skills. Always adjust according to the age of the user and
use for the purpose it has been designed for.

TECHNICAL SPECIFICATIONS

Item:
Item number:
Dimensions when assembled:
Purpose:
If you have assembly problems or would like further information on the product,
we have all you need and more at http://www.hudora.de/service/.
CONTENTS
18 x Goalposts | 1 x Goal net | 1 x Tension cord | 2 x Cover for goal brackets
| 7 x Foam tube closed (pre-assembled) | 2 x Foam tube long (opening on the
back) | 2 x Foam tube short (opening on the back) | 6 x Tent pegs (76914),
7 x Tent pegs (76915) (for stand fixing) | 1 x These instructions
Other items included are meant to facilitate safe transportation and are not re-
quired for the installation and use of the product.
SAFETY INSTRUCTIONS
• WARNING! Not suitable for children under 36 months old due to long cords!
Strangulation Hazard.
• Prior to use, check all parts of the goal for damages and correct assembly.
In this regard, it is important to check the connecting elements and screw
connections for stability and fit. Any sharp edges that might have formed must
immediately be removed!
• Warning: Do not climb on the goal frame or net or hang from the goal posts.
There is a serious risk of injury!
• Children should only use the product when they are under adult supervision.
• No liability is assumed for damages resulting from incorrect application of the
instruction manual.
ASSEMBLY INSTRUCTIONS
Notice: The product must be assembled by 2 adults. Lubricate the connection
assemblies on the narrow ends a bit before starting the assembly. That facilitates
the assembly and extends the durability of the product!
1. Assembling the goalpost frame and net (Fig. 1 and Fig. 2)
Remove all components from the packaging and arrange in front of you correctly
sorted, in particular the numbered tube parts as well as the goal net. Ensure that
the HUDORA logo on the frame encasing is centrally positioned on the crossbar.
It is imperative to pay attention to the order of the assembly, in order to ensure a
smooth assembly, in particular of the frame encasing.
Step 1: The goal rods 1, 2 and 3 are each case present twice in the package,
one with and one without preassembled foam tubes. Slide the goal rods 3, 2 and
1 without preassembled foam tubes (bottom rod), in the tunnel loops A, B and C
of the goal net and then connect the tubes 3, 2 and 1 with the help of the click
connections.
Step 2: Slide the goal rods 6 in the tunnel loops D of the goal net, on both sides.
In order to simplify the assembly, you can open the hook & loop straps on the
tunnel loops. Now close the click connections between the tubes 6 and 3, as well
as between 6 and 1.
Step 3: Slide the padded goal rods 4 in the tunnel loops F and the padded goal
rods 5 in the tunnel loops E of the goal net, on both sides. In order to simplify the
assembly, you can open the hook & loop straps on the tunnel loops. Then close the
click connections between the tubes 4, 5 and 6, on both sides.
All images are examples of the design.
Pro Tect 240 football goal,
Pro Tect 300 football goal
76914, 76915
76914: 240 x 160 x 85 cm,
76915: 300 x 200 x 120 cm
Training goal for versatile throwing, shooting
and goalkeeper training with enhanced impact
protection.
Step 4: Slide the goal rods 1, 2 and 3 with preassembled foam tubes (crossbar) in
the tunnel loops G, H and I of the goal net. The HUDORA logo is centrally positioned
on the tunnel loop H. Then connect the tubes 1, 2 and 3 with the help of the click
connections.
Step 5: Close the click connections between the encased tubes 4 and 1, as well
as between 4 and 3.
Step 6: Mount the covers for the goal corners on both sides (fig. 3). In order to do
this, you should pull both round openings with the inner side over the rear rod end
of rod 1 and 3. Now close the hook and loop closures of the covers around the
crossbar and post. Make sure that the foam tubes are firmly enclosed.
Step 7: Connect the goal rods 7, 8 and 9 for both sides. Then connect these with
the help of a click connection, with the goal frames.
Step 8: Mount the short foam tubes, so that they enclose the click connections
of the cross bar (on the hook & loop strap J). Mount the longer open foam tubes
at the bottom of the two goalposts. Then close all hook & loop straps of the goal
encasing.
Step 9: In order to add additional tension to the goal net, thread the tension cord
through the net, at the height of the rods 9 and tie up the loose ends on the rods.
2. Stand locking of the goal
Finally fix the goal frame by means of the pegs on the ground. Ascertain that the
ground is suitable for the application of pegs (e.g. no water pipes for sprinkler
devices!). Make sure that the pegs are completely driven into the ground and have
firm position. Avoid protruding fastenings (risk of stumbling). On too hard grounds
the goal must be saved by appropriate measures in another way against overtur-
ning in order to prevent risk of injuries (e.g. with slabs or sandbags). Never play
with an unsecured goal or never leave the goal unsecured respectively.
USAGE INSTRUCTIONS
• Only set up the goal on level ground.
• Please keep a minimum distance of at least 3 m to any surrounding obstacles.
• Secure the goal to keep it from toppling over – even if not in use.
• Avoid exposing the product unnecessarily to bad weather conditions. Keep it in
a cool and dry storage area.
• Check for any rust on the product and remove it immediately. Pushing together
the metal parts could lead to the protective layer being scratched and rust
developing.
MAINTENANCE AND STORAGE
Use a dry or damp cloth only to clean the product; do not use special cleaning
agents! Check the product for damage or traces of wear and tear before and after
each use. Do not make any structural changes. For your own safety, please use
original spare parts only. These can be sourced from HUDORA. If parts become
damaged or if sharp edges or corners should develop, the product may not be
used any more. If in any doubt, please contact our service team (http://www.
hudora.de/service/). Store the product in a safe place where it is protected from
the elements, cannot be damaged, and cannot injure anyone.
DISPOSAL ADVICE
At the end of the product's life, please dispose of it at an appropriate collection
point provided in your area. Local waste management companies will be able to
answer your questions on this.
SERVICE
We make every effort to deliver faultless products. If faults do arise however, we
put just as much effort into rectifying them. Therefore, you can find numerous
information on the product, replacement parts, solutions to problems and lost
assembly manuals at http://www.hudora.de/service/.
4/8