Safety Instructions; Electrical Connection - Parker Hiross Hypercool ADS004 Manuel D'utilisation

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 18

1. Safety instructions

!
Every unit is equipped with an electric disconnecting switch
for operating in safe conditions. Always use this device in order to
eliminate risks maintenance.
!
Th e manual is intended for the end-user, only for operations
performable with closed panels: operations requiring opening
with tools must be carried out by skilled and qualifi ed personnel.
Y
Do not exceed the design limits given on the dataplate.
!Y
It is the user's responsibility to avoid loads diff erent from
the internal static pressure. Th e unit must be appropriately pro-
tectedwhenever risks of seismicphenomena exist.
!
Th e safety devices on the compressed air circuit must be pro-
vided for by the user.
Before starting any maintenance operations, make sure that the
circuits are not under pressure.
Only use the unit for professional work and for its intended pur-
pose.
Th e user is responsible for analysing the application aspects for
product installation, and following all the applicable industrial and
safety standards and regulations contained in the product instruc-
tion manual or other documentation supplied with the unit.
Tampering or replacement of any parts by unauthorised personnel
and/or improper machine use exonerate the manufacturer from all
responsibility and invalidate the warranty.
Th e manufacturer declines and present or future liability for dam-
age to persons, things and the machine, due to negligence of the
operators, non-compliance with all the instructions given in this
manual, and non- application of current regulations regarding
safety of the system.
Th e manufacturer declines any liability for damage due to altera-
tions and/or changes to the packing.
It is the responsibility of the user to ensure that the specifi cations
provided for the selection of the unit or components and/or op-
tions are fully comprehensive for the correct or foreseeable use of
the machine itself or its components.
When requesting technical assistance or ordering spare parts, al-
ways quote the model and serial number on the identifi cation plate
mounted externally on the unit.
IMPORTANT:Th e manufacturer reserves the right to modify
this manual at any time.
For the most comprehensive and updated information, the user
is advised to consult the manual supplied with the unit.
2. Introduction
Foreword
Read this manual carefully to ensure that you install and operate
this unit correctly.
Transport / Handling
• Use lift ing equipment of suitable capacity to lift and move the
unit (fork lift etc.).
• Protect the unit from impact to prevent damage to internal
components.
• Th e manufacturer assumes no liability for damages
• Which may be caused by decayed or modifi ed packaging.
English
Inspection
As soon as you receive the unit, check its condition; if you notice
any damage inform the carrier immediately.
3. Assembly (see Fig. 1)
N.B.: For fl anged models, if the optional counterfl anges/gaskets
kit has not been acquired these must be supplied by the user.
3.1 - Mounting aft ercooler
Th e unit can either be wall mounted (using customer supplied
brackets) or fl oor mounted using the legs, either supplied as stand-
ard or available as an optional depending upon the model.
3.2 - Mounting the legs (see Fig. 3)
Place the aft ercooler (1) upside down on the ground; screwthe legs
(3) onto the bottomplate (2) using the nuts and bolts (4).
3.3 - Mounting separator model STH
Screw the separator onto the aft ercooler outlet (for models 004-
009 use the curve (5 - Fig. 3)).
3.4 - Mounting separator model SFH
Connect one gasket and counterfl ange respectively to the aft er-
cooler inlet and separator outlet, using the supplied bolts. Place
the third gasket between the aft ercooler outlet and separator inlet,
and connect those using the supplied bolts.
3.5 - Models 028---064 without separator
Connect one gasket and counterfl ange respectively to the aft er-
cooler inlet and outlet, using the supplied bolts.

3.6 - Electrical connection

Connect the fan power supply cable as indicated in the wiring dia-
gram (see Fig. 6).
ADS/ADT
1

Publicité

Table des Matières
loading

Table des Matières