Others; Connecting The Ac Power Cord - Yamaha DSP-AX2 Mode D'emploi

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 69
Hookups

Others

WARNING
Do not change the IMPEDANCE
SELECTOR switch setting while the power to
this unit is on, otherwise this unit may be
damaged.
IF THIS UNIT FAILS TO TURN ON
WHEN THE STANDBY/ON SWITCH IS
PRESSED:
The IMPEDANCE SELECTOR switch may
not be set to either end. If so, set the switch to
either end when this unit is in the standby
mode.
AC Power Cord
(General, China, and U.K. models)
VOLTAGE SELECTOR
(General and China models)
G.
VOLTAGE SELECTOR
240
IMPEDANCE SELECTOR
SET BEFORE POWER ON
FRONT
: 6ΩMIN./SPEAKER
REAR
: 6ΩMIN./SPEAKER
REAR CENTER
: 6ΩMIN./SPEAKER
CENTER
: 4ΩMIN./SPEAKER
MAIN A OR B
: 4ΩMIN./SPEAKER
A + B
: 8ΩMIN./SPEAKER
FRONT
: 8ΩMIN./SPEAKER
REAR
: 8ΩMIN./SPEAKER
REAR CENTER
: 8ΩMIN./SPEAKER
CENTER
: 8ΩMIN./SPEAKER
MAIN A OR B
: 8ΩMIN./SPEAKER
A + B
: 16ΩMIN./SPEAKER
IMPEDANCE SELECTOR switch
AC Power Cord
(Europe model only)
R
WER ON
N./SPEAKER
N./SPEAKER
N./SPEAKER
N./SPEAKER
N./SPEAKER
N./SPEAKER
N./SPEAKER
N./SPEAKER
N./SPEAKER
N./SPEAKER
N./SPEAKER
IN./SPEAKER
18
IMPEDANCE SELECTOR switch
Select the position whose requirements your speaker system meets.
FRONT EFFECT:
REAR:
REAR CENTER:
CENTER: The impedance of the speaker must be 4Ω or higher.
MAIN:
FRONT EFFECT:
REAR:
REAR CENTER:
CENTER: The impedance of the speaker must be 8Ω or higher.
MAIN:

Connecting the AC power cord

Plug in this unit to a wall outlet when all connections are complete.
AC OUTLETS
Use these to connect the power cords from your other components to this unit. The
power to the switched outlets is controlled by this unit's STANDBY/ON
(SYSTEM POWER or STANDBY on the remote). These outlets will supply
power to any connected unit whenever this unit is turned on. The maximum power
(total power consumption of components) that can be connected to AC OUTLETS
is 100 W.
AC OUTLETS
Voltage selector
The voltage selector on the rear panel of this unit must be set for your local main
voltage BEFORE plugging into the AC main supply.
(Upper position)
The impedance of each speaker must be 6Ω or higher.
The impedance of each speaker must be 6Ω or higher.
The impedance of the speaker must be 6Ω or higher.
If you use one pair of main speakers, the impedance of each speaker
must be 4Ω or higher.
If you use two pairs of main speakers, the impedance of each speaker
must be 8Ω or higher.
(Lower position)
The impedance of each speaker must be 8Ω or higher.
The impedance of each speaker must be 8Ω or higher.
The impedance of the speaker must be 8Ω or higher.
If you use one pair of main speakers, the impedance of each speaker
must be 8Ω or higher.
If you use two pairs of main speakers, the impedance of each speaker
must be 16Ω or higher.
Caution:
• Do not use other AC power cords than the one provided. (Europe model only)
(General and China models)

Publicité

Table des Matières
loading

Table des Matières