Before Using A New Chain Saw - Husqvarna 414 EL Manuel D'utilisation

Masquer les pouces

Table des Matières

Les langues disponibles

lectrical safety

It is recommended that you use a Gorund Fault Circuit

Interrupter (GFCI) with a tripping current of not more than

30mA. Even with a GFCI installed 100% safety cannot be

guaranteed and safe working practice must be followed at

all times. Check your GFCI every time you use it.

Before use, examine the cable for signs of damage or

ageing. If the cable is found to be defective, take the

product to an Authorized Service Center and have the

cable replaced.

Do not use the product if the electric cables are damaged

or worn.

Immediately disconnect from the mains electricity supply if

the cable is cut, or the insulation is damaged. Do not touch

the electric cable until the electrical supply has been

disconnected. Do not repair a cut or damaged cable. Take

the product to an Authorised Service Centre and have the

cable replaced with a genuine spare cable.

Always make sure that the cable/extension cord is kept

behind the user, ensuring that it does not create a source

of danger for the user or for other persons, and check that

it cannot be damaged (by heat, sharp objects, sharp

edges, oil, etc);

Position the cable so that it will not be caught on branches

and the like, during cutting.

Always switch off at the mains before disconnecting any

plug, cable connector or extension cable.

Switch off, remove plug from the mains and examine

electric cable for damage or ageing before winding cable

for storage. Do not repair a damaged cable. Take the

product to an Authorised Service Centre and have the

cable replaced.

Remove the plug from the mains before leaving the product

unattended for any period.

Always wind cable carefully, avoiding kinking.

Use only on AC mains voltage shown on the product rating

label.

The chainsaw is double insulated to EN60745-1 & 2-13.

Make sure your extension cord is in good condition.

Inspect extension cord before use and replace if damaged.

Do not use a damaged cord. Cord insulation must be intact

with no cracks or deterioration. Plug connectors must be

undamaged. Damaged extension cords increase the risk of

electric shock.

Ground Fault Circuit Interrupter (GFCI) protection

should be provided on circuit or outlet to be used.

Receptacles are available having built-in GFCI protection

and may be used for this measure of safety. Inspect chain

saw cords periodically and if damaged, have repaired by an

authorized service dealer.

12 – English

GENERAL SAFETY PRECAUTIONS

WARNING! To reduce the risk of electrical

shock, this equipment has a polarized plug

(one blade is wider than the other) and will

require the use of a polarized extension cord.

The appliance plug will ﬁt into a polarized

extension cord only one way. If the plug does

not ﬁt fully into the extension cord, reverse

the plug. If the plug still does not ﬁt, obtain a

correct polarized extension cord. A polarized

extension cord will require the use of a

polarized wall outlet. This plug will ﬁt into the

polarized wall outlet only one way. If plug

does not ﬁt fully into the wall outlet, reverse

the plug. If the plug still does not ﬁt, contact

a qualiﬁed electrician to install the proper

wall outlet. Do not change the equipment

plug, extension cord receptacle, or extension

cord plug in any way.

Cables

•

Extension cables are available from your local Approved

Service Centre.

•

Only use approved extension cables.

•

If you want to use an extension cable when operating your

product, only the following cable dimensions should be

used: - #14 AWG : max length 7.6 m (25 ft) - #12 AWG :

max length 15 m (50 ft) - #10 AWG : max length 30 m (100

ft) An undersized extension cord will cause a drop in line

voltage resulting in loss of power and overheating. If in

doubt, use the next heavier gauge. The lower the gauge

number, the heavier the cord. Do not use multiple cords.