Publicité
child use it.
• Prolonged exposure to sunlight
can cause fading in fabric and ma-
terials colours.
• Do not use this product with tem-
perature below 5 °C or on slippery
and/or icy surfaces.
• Do not use this product as a sledge
or raft in the water.
• Check the baby walker regularly for
signs of wear and damage.
• Always check that the stoppers are
fitted correctly and show no sign of
damage or tear.
• Do not allow other children to climb
onto or play without the supervision
of an adult near the baby walker.
• When not in use, store the baby
walker in a suitable place, away from
contact with all weather conditions
and out of the reach of children.
• Pay attention when using on floo-
ring made of delicate materials as
the wheels may damage it.
• This baby walking frame is inten-
ded for indoor use only.
• As the child is able to move rapidly
when in a baby walking frame, be
aware that the child can reach ha-
zardous areas in the house, like a
bathtub, household kitchen / laun-
dry appliances, heating devices,
bookshelves / furniture from which
an object can fall, etc
CLEANING & MAINTENANCE
The cleaning and maintenance operations must only be
carried out by an adult.
Clean the fabric and plastic parts including the stopper
with a damp cloth.
Do not use solvents or abrasive products for cleaning.
Dry the metal parts to prevent the formation of rust.
PADDED SEAT COMPOSITION:
100% polyester outer layer, 100% polyurethane inner layer
Wash by hand in cold water
30° C
30° C
COMPONENTS/PARTS
A) Structure of the baby walker
B) Upholstered padded seat
C) Rigid spoiler
D) 2 front swivel wheels
E) 2 rear fixed wheels
F) 6 stoppers
G) Padded seat fixing bands
H) Bar support
FIRST ASSEMBLY OF THE BABY WALKER
1. Turn over the structure (A) of the baby walker. Attach the
front wheels (D) in their slots as shown in figure 1. Make
sure the wheel pin has come to its limit.
2. Attach the rear wheels (E) in their slots as shown in figure
2. Make sure the pin has come to its limit: a click will be
heard and the fastening pin will appear from the hole.
3. Secure all the stoppers (F) in their slots as shown in figure 3.
Make sure that the pins of all the stoppers have come to their limit.
4. Bring the baby walker to position for use by turning the
wheels to the floor (levelled and horizontal); slowly lift the
upper part of the structure as shown in figure 4, by pulling
it upwards until it clicks into place in the desired position.
WARNING: Before putting the child in the baby walker,
make sure the knob located below the upper part of the
structure has reached its engagement position: a click will
be heard to indicate it is locked (fig. 4a). Then push down
the structure to ensure the proper engagement.
5. Insert the front tabs of the rigid spoiler (C) into the slots
cut on the upper part of the structure (A) and push down
on the back until a click is heard locking them (fig. 5).
WARNING: Once the spoiler is inserted it's no longer possi-
ble to pull it out. Do not try to remove it with a screwdriver
or other tool.
6. Insert the padded seat plastic rings (B) in the slots formed
along the top edge of the baby walker (fig. 6) and make sure
they are properly locked in the shown position (fig. 7-8).
WARNING: The bar support must be installed by the par-
ent before allowing the baby to use the walker.
7. The bar support (H) with movable toys is installed by in-
serting side intersections in their seats on the top of the
structure, pushing down until they click (fig. 10-11).
HEIGHT REGULATION OF THE BABY WALKER
WARNING: When opening, closing or regulating the baby
walker, make sure that your child is at a safe distance.
8. To open the baby walker slowly lift the upper part of the
structure by pulling it upwards and supporting it from be-
low until it clicks into the desired position (fig. 4).
9. To adjust the seat height, after taking the child from the
10
Do not bleach
Do not tumble dry
Do not iron
Do not dry clean
Publicité
