Publicité
OBJ_BUCH-0000000540-001.book Page 37 Tuesday, January 16, 2024 2:55 PM
Repair and customer service.
Please observe that power tools may only be
repaired, maintained and inspected by qualified
electricians, as improper maintenance can result in con-
siderable hazards for the user.
When working metal under extreme oper-
ating conditions, it is possible for conductive
dust to settle in the interior of the power
tool. Blow out the interior of the power tool via the
ventilation slots frequently with dry and oil-free com-
pressed air.
When working materials containing gypsum, dust may
occur. This dust can settle inside the power tool as well
as on switching elements and harden in combination
with humidity. As a result, the switching mechanism
may be impaired.
Blow out the interior of the power tool frequently
through the ventilation openings and switching ele-
ments using dry, oil-free compressed air.
Products that have come into contact with asbestos
may not be sent in for repair. Dispose of products con-
taminated with asbestos according to the applicable
country-specific regulations for such disposal.
For FEIN power tools and accessories in need of repair,
please contact your FEIN after-sales service. The
address can be found on the Internet under
www.fein.com.
Renew stickers and warning indications on the power
tool when aged and worn.
The current spares parts list for this power tool can be
found on our website at www.fein.com.
Use only original spare parts.
If required, you can change the following parts your-
self:
Application tools, clamping flanges (where applicable),
wheel guard, battery, auxiliary handle, dust-protection
filter, hand protection
Maintenance and cleaning.
Occasionally clean the ventilation slots and the battery
terminals with a soft, clean and dry brush.
– Do not use chemical substances for cleaning the bat-
tery.
Warranty and liability.
The warranty for the product is valid in accordance
with the legal regulations in the country where it is mar-
keted. In addition, FEIN also provides a guarantee in
accordance with the FEIN manufacturer's warranty dec-
laration.
The delivery scope of your power tool may include
only a part of the accessories described or shown in this
Instruction Manual.
Declaration of conformity.
This CE declaration is only valid for European Union
and EFTA (European Free Trade Association) countries
and only for products intended for the EU or EFTA
market. After placing the product on the EU market the
UKCA mark loses its mark validity.
The UKCA declaration is only valid for the Great
Britain market (England, Wales and Scotland) and only
for products intended for the Great Britain market.
After placing the product on the Great Britain market
the CE mark loses its mark validity.
Environmental protection, disposal.
Do not dispose of the batteries into household-
waste!
Packaging, worn out power tools and accessories
should be sorted for environmental-friendly recycling.
Dispose of batteries only when discharged.
For batteries that are not completely discharged, insu-
late the terminals with tape as a protective measure
against short-circuiting.
Only for EC countries:
According to the European Guideline 2002/66/EC,
defective or used battery packs/batteries, must be col-
lected separately and disposed of in an environmental-
lycorrect manner.
Selection of accessories
(see pages 16 – 20).
Use only original FEIN accessories. The accessories
must be intended for the power tool type.
A-1 Wheel guard for cutting, type A
B-1 Wheel guard for grinding, type B
1-1 Grinding disc, type 27
2-1 Cutting disc
(use only with cut-off wheel guard, Type A)
3-1 Flap discs
3-2 Backing pad for fibre sanding sheets, fibre sanding
sheets
(mount only with the provided backing-pad clamp-
ing unit)
3-3 Backing pad with Velcro, Velcro sanding sheets,
sanding fleece with Velcro attachment, sponges
(Only CCG18-125-7 AS (**): Use a fitting open-
end spanner)
4-1 Steel tapered twist brush
4-2 Steel-wire cup brush, flap discs
(Only CCG18-125-7 AS (**): Use a fitting open-
end spanner)
5-1 Diamond hole cutter
(Only CCG18-125-7 AS (**): Use a fitting open-
end spanner)
en
37
Publicité
