Publicité
OBJ_BUCH-0000000540-001.book Page 32 Tuesday, January 16, 2024 2:55 PM
en
32
Character
Unit of measurement,
international
K...
2
m/s
2
m/s
h,AG
2
m/s
h,DS
m, s, kg, A, mm, V, W,
N, °C, dB, min, m/s
For your safety.
Read all safety warnings and all
WARNING
instructions. Failure to follow the
warnings and instructions may result in electric shock,
fire and/or serious injury.
Save all warnings and instructions for future reference.
Do not use this power tool before you have
thoroughly read and completely understood this
Instruction Manual and the enclosed "General
Safety Instructions" (document number
3 41 30 465 06 0). The documents mentioned should
be kept for later use and enclosed with the power tool,
should it be passed on or sold.
Please also observe the relevant national industrial
safety regulations.
Intended use of the power tool:
The hand-guided, battery-operated angle grinder is
intended for cutting, roughing and brushing of metal
and stone materials as well as for drilling stone materials
with diamond core bits without the use of water.
For cutting with bonded abrasives, a special cut-off
wheel guard must be used.
When cutting in stone, provide for sufficient dust
extraction.
With approved sanding tools, the machine can be used
for sanding with sanding discs.
The power tool must not be used for grinding concrete.
Safety warnings common for grinding, sanding,
wire brushing or cutting-off operations
This power tool is intended to function as a grinder,
sander, wire brush, hole cutter or cut-off tool. Read all
safety warnings, instructions, illustrations and specifi-
cations provided with this power tool. Failure to follow
all instructions listed below may result in electric shock,
fire and/or serious injury.
Operations such as polishing are not to be performed
with this power tool. Operations for which the power
tool was not designed may create a hazard and cause
personal injury.
Do not convert this power tool to operate in a way which
is not specifically designed and specified by the tool
manufacturer. Such a conversion may result in a loss of
control and cause serious personal injury.
Do not use accessories which are not specifically
designed and specified by the tool manufacturer. Just
because the accessory can be attached to your power
tool, it does not assure safe operation.
Explanation
Uncertainty
Vibrational emission value according to EN 62841 (vector sum of
three directions)
Mean vibrational value for angle grinding
Mean vibrational value for sanding with sanding sheet
Basic and derived units of measurement from the international
2
system of units SI.
The rated speed of the accessory must be at least equal
to the maximum speed marked on the power tool.
Accessories running faster than their rated speed can
break and fly apart.
The outside diameter and the thickness of your acces-
sory must be within the capacity rating of your power
tool. Incorrectly sized accessories cannot be adequately
guarded or controlled.
The dimensions of the accessory mounting must fit the
dimensions of the mounting hardware of the power
tool. Accessories that do not match the mounting hard-
ware of the power tool will run out of balance, vibrate
excessively and may cause loss of control.
Do not use a damaged accessory. Before each use
inspect the accessory such as abrasive wheels for chips
and cracks, backing pad for cracks, tear or excess
wear, wire brush for loose or cracked wires. If power
tool or accessory is dropped, inspect for damage or
install an undamaged accessory. After inspecting and
installing an accessory, position yourself and bystand-
ers away from the plane of the rotating accessory and
run the power tool at maximum no-load speed for one
minute. Damaged accessories will normally break apart
during this test time.
Wear personal protective equipment. Depending on
application, use face shield, safety goggles or safety
glasses. As appropriate, wear dust mask, hearing pro-
tectors, gloves and workshop apron capable of stopping
small abrasive or workpiece fragments. The eye pro-
tection must be capable of stopping flying debris gener-
ated by various applications. The dust mask or
respirator must be capable of filtrating particles gener-
ated by the particular application. Prolonged exposure
to high intensity noise may cause hearing loss.
Keep bystanders a safe distance away from work area.
Anyone entering the work area must wear personal pro-
tective equipment. Fragments of workpiece or of a bro-
ken accessory may fly away and cause injury beyond
immediate area of operation.
Hold the power tool by insulated gripping surfaces only,
when performing an operation where the cutting acces-
sory may contact hidden wiring. Cutting accessory con-
tacting a "live" wire may make exposed metal parts of
the power tool "live" and could give the operator an
electric shock.
Never lay the power tool down until the accessory has
come to a complete stop. The spinning accessory may
grab the surface and pull the power tool out of your
control.
Publicité
