Publicité
GB
All end users are responsible for deleting any
personal data stored on waste devices prior
to their disposal.
Disposal of the packaging
The packaging consists of cardboard
and correspondingly marked plastics
that can be recycled.
– Make these materials available
for recycling.
Technical data
Item number
Pruning saw
Idling speed
Length of the saw bar 200 mm
Cutting speed
Oil tank capacity
Noise pressure level
(L
)*
PA
Sound power level
(L
)*
WA
Vibration**
• Grip for front hand
• Grip for rear hand
Weight
Saw bar
Saw chain
Max. operating dura-
tion with a full 2Ah bat-
tery
Hedge trimmer
Cutting length
Max. branch diameter 16 mm
Stroke rate
Acoustic pressure
(L
)*
PA
Acoustic power (L
WA
Vibration**
• Grip for front hand
• Grip for rear hand
Weight
68
196023
-1
1800 min
4,5 m/s
100 ml
77,8 dB(A)
(K = 3 dB(A))
87,8 dB(A)
(K = 2,72 dB(A))
2,55 m/s²
2,48 m/s²
(K = 1,5 m/s²)
ca. 3,1 kg
• Oregon
080SDEA041
• TriLink
M1500833-
1041TL
• Oregon
91PJ033X
• TriLink
CL15033TL
50 min
410 mm
−1
2400 min
77,9 dB(A)
(K = 3 dB(A))
)* 89 dB(A)
(K = 2,19 dB(A))
3,04 m/s²
2,69 m/s²
(K = 1,5 m/s²)
ca. 3,5 kg
Item number
Max. operating dura-
tion with a full 2Ah bat-
tery
*)
The noise emission values indicated have been measured
according to a standardized test method and can be used to
compare one power tool with another. The noise emission val-
ues indicated can also be used for a preliminary assessment of
the exposure. Warning: The noise emissions during the actual
use of the power tool may differ from the indicated values,
depending on the way in which the power tool is used, in particu-
lar what type of workpiece is being machined. Safety measures
must be defined to protect the operator, based on an estimation
of the vibration load during actual conditions of use (taking into
consideration all parts of the operating cycle, such as time peri-
ods when the power tool is switched off and time periods when
it is switched on but running without a load).
**) The specified vibration emission value was measured in accord-
ance with a normed test procedure and can be used in order to
compare one tool with another. The specified vibration emission
value can also be used for an introductory evaluation of the
exposure. The vibration emission value may fluctuate from the
specified value during actual use of the power tool. These fluc-
tuations will depend on the way in which the power tool is used.
Try to keep vibrations to a minimum. One method of reducing
the vibration load is, for example, limiting the length of time you
work with the tool. All parts of the operating cycle must be taken
into account for this purpose (for example, also including times
in which the power tool is switched off and times in which it is
switched on, but is running without load). Determination of vibra-
tion emission values in accordance with EN 62841-
1, EN 62841-4-2 & EN ISO 11680-1.
Appropriate chain oil
NOTICE! Risk of damage to the
device! Under no circumstances
should you use old oil to grease the
saw chain! This can cause damage to
the oil pump, saw bar and chain!
Use only special saw chain oils with good
adhesion properties. Since the saw chain oil
can penetrate the environment during opera-
tion, biologically-degradable special vegeta-
ble-based saw chain oils should be used.
Accessories
You can find more information
about suitable batteries and
spare parts of the 1 Power Sys-
tems here: see QR Code
196023
50 min
Publicité
