Publicité
WARNING!
This machine should only be used with a continuos rin diamond disc. Do not use this machine
with a segmented or turbo disc.
If the disc is mistakenly mounted and when machine is turned on is running in the opposite
direction, stop the machine and correctly re-mount before commencing any work.
Workspace
Workspace
Assembly
Once you have unpacked your machine, check to make sure that there are no damaged or broken
parts. If there are, and you need to change these components they must only be replaced by original of
the manufacturer (if in doubt, consult the manufacturer).
Safety
Read carefully and understand the safety measures before the use of the machine.
Hooking up
Check that the voltage and frequency of the machine shown on the characteristics plate match the
Coil feeding cable during transport. Never move the machine by tugging at the cable.
Applications
Use: Models DU-EVO are basic machines for the straight or mitred cutting of building materials, and
work by means of a guided bearing system. Such cuts are made with water-cooled diamond blades.
Recommendations concerning the work area
Pay close attention to the state of the area where the job is to be done. Keep it clean and well lit. The
machine should be kept clean at all times in order to ensure optimum performance and the safest
working conditions.
Items to be checked before starting the machine
1.
any part that is not in proper condition, have it repaired or replaced immediately.
2.
Check that the stops of the machine are perpendicular to the blade. These are regulated before
4.
Ensure that the voltage and frequency of the machine shown on the characteristics plate match
5.
The electrical outlet must have an earth connection and protection in the event of leaking
6.
The disc cover protection, protects to the user of possible cuts during the work.
7.
8.
6, 7) and following these steps:
9.
Deploy the legs of the machine, making sure that are perfectly open.
10.
11.
Put the water pump into the tank.
12.
Machine's head has a breaking system to avoid any movement during transport. To start cutting,
1.
the blade between the blade discs, turning in the direction shown on the machine. Tighten the
screw as illustrated 11, 12.
2.
Fill the base with water until the water pump is completely covered. Working with clean water gives
Models DU-EVO are equipped with a table-stand for placing the ceramic tile, and.a sliding motor
unit. This system enables you to handle all types of ceramic tile with maximum precision and
4.
Movement takes place by means of wheels equipped with greased, sealed ball bearings.
5.
that of mitred cutting (and viceversa), changing cutting height and adjusting stops for repeated
cuts.
6.
The starting of the machine will be made by pressing the tilted switch, and the same to
7.
DU-EVO have a safety system that protects the motor from overheating.
8.
If the motor should stop for no apparent reason, wait a few minutes as it has probably been
overworked. Moderate the speed in subsequent cutting.
9.
Once the machine is operating, wait until the motor and the water supply by the pump return
to normal (4 or 5 seconds).
10.
can break the workpiece and seriously damage the blade.
11.
For 45º cuts (mitred cuts), there is a system of mechanical blockage, which enables you to
12.
· TRANSLATION OF THE ORIGINAL ·
14.
Never use diamond blades that are cracked or chipped.
15.
Never use lateral pressure to stop the blades.
16.
Read these instructions carefully before using this product. Keep them in a safe place for future
reference.
17.
Keep cutting tools clean and sharp for better, safer performance:
• Carefully follow instructions when changing accessories.
• Periodically check the cables of this machine. Should they show signs of damage or
wear and tear, have them repaired at an authorised technical service outlet.
• Keep holders clean, dry and free of grease and oil..
18.
Remove wrenches and tools before switching on the machine.
19.
20.
When using the machine outdoors, use only extensible cord designed for this purpose.
21.
Before using a machine again, check carefully to ensure that it is in proper working. order for
the task you have in mind for it. Any damaged element, whether protective or not, should be
22.
.
T
24.
C
and to choose between an improved cleaning (higher position, recommended for abrasive
materials) or better cooling (lower position, recommended for hard materials). C SYSTEM
optimizes water's consume by reducing its loss.
Cleaning and maintenance
1.
Before cleaning, maintenance or repair of the machine, or transport, the machine must be
2.
Do not use aggressive cleaning products for cleaning the machine.
The machine must not be immersed in water.
4.
Examine periodically the machine cables, if they are damaged must repair them through an
authorized technical service.
5.
You must maintain the grips dry, clean and free of fat and oil.
6.
it and run clean water through the cooling system,especially to clean the submer sible pump.
for assistance.
Storage
Store the machine in a cool, dry, place, protected from direct sunlight.
The decommissioning and dismantling of the machine must be carried out according to the instructions
Use only accessories and original spare parts supplied by the manufacturer. Repairs should only be
carried out by an accredited workshop or RUBI technical support:
GERMANS BOADA SANTA OLIVA
Tarragona (Spain)
Images.......................................................................................................................................................................................Pag.60
Technical characteristics...................................................................................................................................................Pag.62
The overall machine............................................................................................................................................................Pag.62
Accessories..............................................................................................................................................................................Pag.62
Electric mitring saws for tiles....................................................................................................................................Pag.62
Decalaration of compliance with eec regulations...........................................................................................Pag.65
Warranty..............................................................................................................................................................................Pag.69
EN
- 7 -
Publicité
