Publicité
position in the impact socket groove to retain the pin.
To remove the impact socket, follow the installation
procedures in reverse.
► Fig.10: 1. Impact socket 2. O-ring 3. Pin
For impact socket without O-ring and pin
Only for model TW002G
Push the impact socket onto the square drive until it
locks into place.
To remove the impact socket, simply pull it off.
► Fig.11: 1. Impact socket 2. Square drive 3. Ring
spring
Tool with the detent pin
For tool with firm fit detent pin
Only for model TW003G
To install the impact socket, align the hole in the
side of the impact socket with the detent pin on the
square drive, and then, push it onto the square drive
until it locks into place. Tap the impact socket lightly if
required.
To remove the impact socket, depress the detent pin
through the hole in the impact socket and pull the
impact socket off the square drive.
► Fig.12: 1. Impact socket 2. Hole 3. Square drive
4. Detent pin
NOTE: The firm fit detent pin may fit too securely to
remove the impact socket.
In that case, depress the firm fit detent pin fully and
pull the impact socket off the square drive.
Installing hook
WARNING:
Use the hanging/mounting parts
for their intended purposes only, e.g., hanging the
tool on a tool belt between jobs or work intervals.
WARNING:
Be careful not to overload the
hook as too much force or irregular overburden
may cause damages to the tool resulting in per-
sonal injury.
CAUTION:
When installing the hook, always
secure it with the screw firmly. If not, the hook
may come off from the tool and result in the personal
injury.
CAUTION:
Make sure to hang the tool
securely before releasing your hold. Insufficient
or unbalanced hooking may cause falling off and you
may be injured.
The hook is convenient for temporarily hanging the tool.
This can be installed on either side of the tool. To install
the hook, insert it into a groove in the tool housing
on either side and then secure it with two screws. To
remove, loosen the screws and then take it out.
► Fig.13: 1. Groove 2. Hook 3. Screw
Ring
Country specific
CAUTION:
Before using the ring, always
make sure that the bracket and ring are secured
and not damaged.
CAUTION:
Use the hanging/mounting parts
for their intended purposes only. Using for unin-
tended purpose may cause accident or personal
injury.
The ring is convenient for hanging the tool with hoist.
First, place the rope through the ring. Then hang the
tool up to the air with hoist.
► Fig.14: 1. Bracket 2. Ring 3. Screws
OPERATION
CAUTION:
Always insert the battery cartridge
all the way until it locks in place. If you can see the
red indicator on the upper side of the button, it is not
locked completely. Insert it fully until the red indicator
cannot be seen. If not, it may accidentally fall out of
the tool, causing injury to you or someone around
you.
Hold the tool firmly and place the impact socket over
the bolt or nut. Turn the tool on and fasten for the proper
fastening time.
The proper fastening torque may differ depending upon
the kind or size of the bolt, the material of the workpiece
to be fastened, etc. The relation between fastening
torque and fastening time is shown in the figures.
► Fig.15
Model TW001G/TW002G
Proper fastening torque for high tensile bolt with
max impact mode (4)
N•m
(kgf•cm)
1600
(16315)
1400
(14276)
1200
(12236)
1000
(10197)
800
2
(8157)
600
(6118)
400
(4078)
200
(2039)
0
1. Fastening time (second) 2. Fastening torque
11 ENGLISH
M27
M24
1
2
1
M27
M24
3
Publicité
