Specific Safety Instructions; Instructions For Use; Placement Tool; Ilustrated Description - stayer RO751E Instructions D'emploi

The machine is intended for dry sanding of wood, plastic,
metal, filler as well as coated surfaces.
Machines with electronic control are also suitable for
polishing.
1. Contents
2. Specific safety instructions ........................... 15
3. Instructions for use ........................................ 15
3.1 Placement tool .................................................... 15
3.2 Assembly............................................................. 15
3.3 Ilustrated description ........................................... 15
4. Operating instructions ................................... 15
4.1 Placement and testing ........................................ 15
4.2 Tool change ......................................................... 16
4.3 Instructions for use.............................................. 16
5. Maintenance and service instructions ......... 17
5.1 Cleaning .............................................................. 17
5.2 Repair service ..................................................... 17
5.3 Warranty ............................................................. 17
5.4 Disposal and recycling ........................................ 17
6. Regulations ..................................................... 18
6.1 Technical Data .................................................... 18
6.2 EU declaration of conformity. .............................. 18

2. Specific safety instructions

- Use the machine only for dry sanding. Penetration of
water into the machine increases the risk of an electric
shock or damaged.
- Pay attention that no persons are put at risk through
sparking. Remove any combustible materials in
the vicinity. Sparking occurs when sanding metal
materials.
- Caution, fire hazard! Avoid overheating the object
being sanded as well as the sander. Always
empty the dust collector before taking breaks. In
unfavourable conditions, e. g., when sparks emit from
sanding metals, sanding debris in the dust bag, micro
filter or paper sack (or in the filter sack or filter of the
vacuum cleaner) can selfignite. Particularly when
mixed with remainders of varnish, polyurethane or
other chemical materials and when the sanding debris
is hot after long periods of working.
- When working with the machine, always hold it firmly
with both hands and provide for a secure stance. The
power tool is guided more secure with both hands.
- Secure the workpiece. A workpiece clamped with
clamping devices or in a vice is held more secure than
by hand.
ENGLISH
15

3. Instructions for use

3.1 Placement tool

Read all safety warnings and all instructions.
Failure to follow the warnings and instructions
may result in electric shock, fire and/or
serious injury.
page
While reading the operating instructions, unfold the
graphics page for the machine and leave it open.
Use this power tool for dry sanding or polishing
3.2 Assembly (figure1).
Before any work on the machine itself, pull the
mains plug.
The machine is completely assembled, except
sanding sheet 8.
To position the sanding sheet 8 should attach to velcro support
plate 5, taking into account that the suction holes coincide.
Auxiliary handle
The auxiliary handle 10 allows comfortable handling
and even distribution of force, especially if the material
removal rate is high.
Screw the auxiliary handle 10 to the right or left on the
spindle thread 1.

3.3 Ilustrated description

The numbering of the product features refers to the
illustration of the machine on the graphics page.
1 Rubber Head.
2 Suction nozzle.
3 Wick holder.
4 Catch.
5 Back plate.
6 Sanding plate screws.
7 Key.
8 Sanding sheet *.
9 Grip (nip isolated).
10 Auxiliary handle.
11 Switch on / off.
12 Suction tube.
13 Screw fastening the suction tube.
14 Thumbwheel for preselection of number
of oscillations.
15 Regulatory control of the orbit.
* Accessories shown or described are not part of the standard
delivery scope of the product. A complete overview of accessories
can be found in our accessories program.

4. Operating instructions

4.1 Placement and testing

Network connection
Observe correct mains voltage! The voltage of the
power source must agree with the voltage specified on
15