DeWalt DCD791 Traduction De La Notice D'instructions Originale page 21

Date Code Position (Fig. A)
The production date code 16
by a 2-digit week and is extended by a 2-digit factory code.
Description (Fig. A)

WARNING: Never modify the power tool or any part of it.
Damage or personal injury could result.
Trigger switch
1
Forward/reverse control button
2
Torque adjustment collar
3
Gear shifter
4
Worklight
5
Keyless chuck
6
Belt hook
7
Mounting screw
8
Bit holder
9
Battery pack
10
Battery release button
11
Worklight switch
12
Low light mode
13
Medium light mode
14
Spotlight mode
15
Date code
16
Intended Use
These drills/drivers/hammerdrills are designed for professional
drilling, percussion drilling and screwdriving applications.
DO nOT use under wet conditions or in the presence of
flammable liquids or gases.
These drills/drivers/hammerdrills are professional power tools.
DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
• Young children and the infirm. This appliance is not
intended for use by young children or infirm persons
without supervision.
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or mental
abilities; lack of experience, knowledge or skills unless they are
supervised by a person responsible for their safety. Children
should never be left alone with this product.
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal injury,
turn tool off and disconnect battery pack before making
any adjustments or removing/installing attachments or
accessories. An accidental start-up can cause injury.

WARNING: Use only D
e
Inserting and Removing the Battery Pack from the
Tool (Fig. B)
nOTE: Make sure your battery pack
To Install the Battery Pack into the Tool Handle
1. Align the battery pack with the rails inside the tool's
handle (Fig. B).
2. Slide it into the handle until the battery pack is firmly seated
in the tool and ensure that you hear the lock snap into place.
consists of a 4-digit year followed
WALT batteries and chargers.
10 is fully charged.
To Remove the Battery Pack from the Tool
1. Press the battery release button
battery pack out of the tool handle.
2. Insert battery pack into the charger.
Fuel Gauge Battery Packs (Fig. B)
Some D WALT battery packs include a fuel gauge, which
e
consists of three green LED lights that indicate the level of
charge remaining in the battery pack.
To actuate the fuel gauge, press and hold the fuel gauge
button 17 . A combination of the three green LED lights will
illuminate, designating the level of charge left. When the level
of charge in the battery is below the usable limit, the fuel gauge
will not illuminate and the battery will need to be recharged.
nOTE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end-user application.
Belt Hook and Magnetic Bit Holder (Fig. A)
Optional Accessories

WARNING: To reduce the risk of serious personal injury,
ONLY use the tool's belt hook to hang the tool from a work
belt. DO NOT use the belt hook for tethering or securing the tool
to a person or object during use. DO NOT suspend tool overhead
or suspend objects from the belt hook.

WARNING: To reduce the risk of serious personal injury,
ensure the screw holding the belt hook is secure.

CAUTION: To reduce the risk of personal injury or
damage, DO NOT use the belt hook to hang the drill while
using as a spotlight.
IMPORTanT: When attaching or replacing the belt hook
magnetic bit holder , use only the mounting screw
9
provided. Be sure to securely tighten the screw.
The belt hook and magnetic bit holder can be attached to either
side of the tool using only the screw provided, to accommodate
left- or right-handed users. If the hook or magnetic bit holder is
not desired at all, it can be removed from the tool.
To move belt hook or magnetic bit holder, remove the screw
that holds it in place, then reassemble on the opposite side. Be
sure to securely tighten the screw.
Variable Speed Trigger Switch (Fig. A)
To turn the tool on, squeeze the variable speed
trigger switch 1 . To turn the tool off, release the trigger switch.
Your tool is equipped with a brake. The chuck will stop as soon
as the trigger switch is fully released.
nOTE: Continuous use in variable speed range is not
recommended. It may damage the switch and should
be avoided.
Forward/Reverse Control Button (Fig. A)
A forward/reverse control button
the tool and also serves as a lock-off button.
To select forward rotation, release the trigger switch and
depress the for ward/re verse control button on the right side of
the tool.
To select reverse, release the trigger switch and depress the
forward/reverse control button on the left side of the tool.
EnGLIsH
11 and firmly pull the
7
that is
8
determines the direction of
2
or
19