Publicité
after removing the collection bag and closes off
the rear chute opening. If any grass remains in
the opening, it will be easier to restart the engine
if you pull the mower back approximately 3.2 feet
(1m).
Do not use your hands or feet to remove clippings
in or on the mower housing, but instead use suita-
ble tools such as a brush or a hand broom.
In order to ensure that the majority of grass
clippings are picked up, the inside of the
collection bag must be cleaned after each use.
Reattach the collection bag only when the motor
is switched off , the safety plug has been pulled
out and the blade has stopped.
Lift up the chute fl ap with one hand and, holding
the collection bag by its handle with the other
hand, hang in the collection bag from the top.
7. Cleaning and maintenance
Danger!
Pull out the safety plug (16) and remove all the
batteries (25) before starting any cleaning work.
7.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it down with compressed air at
low pressure.
•
Do not clean the lawn mower with running
water, particularly with high-pressure water.
•
We recommend cleaning the equipment
immediately each time after use.
•
Clean the equipment regularly with a damp
cloth and some soft soap. Do not use
cleaning agents or solvents; these may
be aggressive to the plastic parts in the
equipment. Ensure that no water can get into
the interior of the equipment. The ingress of
water into an electric power tool increases the
risk of an electric shock.
•
For best results, clean the lawn mower with a
brush or rag.
7.2 Maintenance
•
Worn out or damaged blades, blade mounts,
and bolts should be replaced as a set by an
authorized professional in order to keep the
equipment in balance.
Anl_GP_CM_36_52_S_Li_BL_SPK7_NA.indb 17
Anl_GP_CM_36_52_S_Li_BL_SPK7_NA.indb 17
EN
•
Ensure that all mounting components (i.e.
screws, bolts, nuts, etc.) are always tightened
so that the equipment can be safely operated
at all times.
•
Frequently check the collection bag assembly
for signs of wear.
•
Replace excessively worn or damaged parts
immediately.
•
In order to ensure that you enjoy the
equipment for many years to come, all
screwed parts, as well as the wheels and
axles, should be cleaned and lubricated.
•
Keeping your lawn mower in good condition
not only ensures a long lifespan and high
performance, but also enables the equipment
to thoroughly cut your grass with minimal
effort.
•
The blade is subjected to more wear and
tear than any other component. Therefore,
routinely check the condition of the blade
and make sure that it is tightly fastened. If
the blade is completely worn out, it must be
immediately replaced or ground sharp again.
An excessively vibrating mower means that
the blade is not properly balanced or has
become deformed from striking an object.
In this case, the blade must be repaired or
replaced.
•
There are no other parts inside the equipment
which require maintenance.
Lamps can be replaced by only replacement
parts from the manufacturer.
7.3 Replacing the blade
For safety reasons, we recommend having the
blade replaced by an authorized professional.
Important! Wear work gloves! Only replace the
blade with a genuine Einhell replacement blade,
as this will ensure top performance and safety
under all conditions.
Carry out the following steps to change the
blade:
1. Undo the fastening screw.
2. Remove the blade and replace with a new
one.
3. When fi tting the blade, make sure it is
installed in the right direction. The blade
air vanes must project into the motor
compartment. The dome mounts must be
aligned with the punch holes in the blade.
4. Then retighten the fastening screw with the
universal wrench. The tightening torque
should be approx. 18.4 ft./lbs (25 Nm).
- 17 -
23.07.2024 08:59:53
23.07.2024 08:59:53
Publicité
