Publicité
DocuSign Envelope ID: 5674BC8F-4441-43F9-A79E-6A4828D74913
The manufacturer herewith declares that the equipment is in conformity with the UK statutory requirements.
(1)
(2)
Equipment type
Applicable
(3)
Directives
(9)
Approved body
(10)
This partly completed machinery must not be put into service until the final machinery in which it is
to be incorporated has been declared in conformity with Supply of Machinery (Safety) Regulations 2008.
SAMES KREMLIN is allowed to compil the technical documentation. SAMES KREMLIN undertakes to
transmit, in response to a reasoned request by the national authorities, relevant information on the partly
completed machinery in the most appropriate form. This declaration of incorporation of partly completed
machinery and this declaration of conformity are issued under the sole responsibility of the
manufacturer.
Director of the STAINS site - Executive Management (EM)
Hervé WALTER
Established in Stains, on
Siège Social / Headquarter: 13, chemin de Malacher - CS70086 - 38243 Meylan Cedex - France - Tél / Phone: +33 (0)4 76 41 60 60
(4)
The relevant technical documentation was compiled as
The essential health and safety requirements mentioned in Supply of Machinery
2008 No.
(Safety) Regulations 2008 have been applied.
1597
Articles: 1.1.5 ,1.1.6, 1.3.1, 1.3.2, 1.3.4, 1.5.1, 1.5.2
(5)
That partly completed machinery is also in conformity with the provisions of
2016 No. 1107
Marking
(6)
(7)
Designated
standards
Conformity
(8)
assessment
procedure
2016 No. 1091
2016 No. 1101
2013 No. 3113
Waste Electric and Electronic Equipment (WEEE) Regulations 2013
Approved Bodies INERIS 0080 – 60550 Verneuil-en-Halatte- France /
n° INERIS-CERN 038002/ 22.
21CLM 25031 - Ellesmere Port - United Kingdom /
CML n°22UKEXT747 Issue 0
16-déc.-22 | 19:27 CET
SAS au capital de 12.720.000 euros | RCS Grenoble: 572 051 688 | Code APE: 2829B | TVA intracom: FR36 572051688
DECLARATION OF INCORPORATION
OF PARTLY COMPLETED MACHINERY
UK DECLARATION OF CONFORMITY
Electronic Dosing System Cyclomix
specified in annex VII, part B.
Electronic Dosing System
II 2G Ex h IIB T4 Gb X => dosing system in ATEX Zone
II (2)G Ex[ia Gb] IIB => piloting box outside of ATEX zone
Equipment
Zener barrier
Electrovalve ATEX
Sensor element ATEX
Mass Flowmeter
Cylinder
Pressure sensor
Fiber optic amplifier sensor
Each individual electrical component used in zone 1 is in
conformity
with
Their combined presence in the assembly has not highlighted
any ad- ditional risks that would necessitate a comprehensive
assesment of this type of machinery.
EN ISO 80079-36 : 2016
EN ISO 80079-37 : 2016
EN 1127-1 : 2019
Module A Technical documentation (Annex VIII)
The Electromagnetic Compatibility Regulations 2016
Low Voltage Directive
Sames
1
Evo
®
Approval N°
BAS 01 ATEX 7005
LCIE 12 ATEX 3005 X
BVS 08 ATEX E 101
BVS 17 ATEX E 074
21 ATEX 0036
SEV 11 ATEX 0129
BVS 17 ATEX E 041
the
2016
No.
1107
DEC UK 578156130
directive.
Publicité
