Dremel 2200 VERSAFLAME Traduction De La Notice Originale page 5

Make sure the gas you are using is refined butane gas
that can also be used for lighters.
1 . Hold the tool and the gas refill container as shown
in .
3
2 . Fill the gas tank with liquid butane gas observing
the instructions on the refill container. The gas
tank is full when liquid butane gas escapes
through the filling valve. In that case, there is no
more air present in the gas tank.
DO NOT OVERFILL THE GAS TANK.
!
Overfilling occurs when no air escapes from the
tank while filling it. In this case please use a different
tip on the gas tank with which you are filling, to allow
air to escape from the tank.
USE
GETTING STARTED
Familiarize yourself with the components of the tool
.
2
The tool is equipped with a child-safety mechanism
which requires a two-step operation to protect against
accidental ignition.
ON/OFF
To switch on and operate the tool
1 . The air control lever must be in the open position
a .
4
2 . The lock button must be in the forward position for
the tool to be able to ignite
3 . Hold the tool in one hand.
4 . With your other hand move the child-safety lock
to the left c .
4
5 . Slowly press the ignition button and hold it down
d .
4
6 . When using the catalyst: close the air control
lever for 2 seconds and re-open it to prevent the
catalyst from being overheated
After ignition, make sure that the tool is
switched on by checking that the catalyst
starts to glow.
7 . To switch off the tool, release the ignition button.
This will immediately shut off the flow of butane
gas .
To operate the tool continuously
1 . Switch on the tool as described above.
2 . Slide the lock button backward and release the
ignition button.
3 . To switch off the tool, slide the lock button forward.
This will immediately stop the flow of butane gas.
USING WITH AN OPEN FLAME
The tool can only be used with an open flame if the
catalyst is removed.
FLAME LENGTH AND TEMPERATURE
ADJUSTMENT
Move the flame control lever forward to increase
the flame length and temperature, or backward to
decrease the flame length and temperature.
When using an open flame, the tool is at the desired
temperature immediately after ignition.
Please allow approximately 25 seconds of heat-up
time for the soldering tip.
ATTACHING OR REMOVING ACCESSORIES
CATALYST B
The catalyst generates hot air of 680°C (used for
melting plastics and other heat-sensitive materials):
1 .
2 .
SOLDERING TIP A
The soldering tip, to be used on the catalyst (used for
regular soldering activities, using soldering tin):
1 .
2 .
FLAME EXTENSION PIECE L
The flame extension piece generates hot air of approx.
1000°C (used for heating larger surfaces):
: 1 .
4
DEFLECTOR M
b . To be used with the flame extension piece.
4
CLEANING
e .
4
Clean the exterior of the tool with a clean cloth. If
necessary, use a damp cloth with a small amount of
neutral detergent.
After soldering or in case of excess solder on the
soldering tip, wipe the tip on a soldering sponge
soaked in some water when it is still hot.
: Never clean the soldering tip with sandpaper as this
5
reduces its lifetime.
We recommend that all tool service be performed by a
Dremel Service Centre.
This Dremel product is guaranteed in accordance with
statutory/country-specific regulations; damage due to
normal wear and tear, overload or improper handling
are excluded from the warranty.
In case of a complaint, send the undismantled tool
and/or charger and proof of purchase to your dealer.
CONTACT DREMEL
For more information on service and warranty, the
Dremel product range, support and hotline, go to
www .dremel .com .
5
ACCESSORIES
ALWAYS SWITCH OFF THE TOOL AND
!
ALLOW IT TO FULLY COOL DOWN BEFORE
6
Slide the narrow part of the catalyst into the
burner. Make sure the slot of the catalyst is
aligned with the white indicator mark.
To remove the catalyst, slide it out of the burner.
7
Screw the soldering tip in clockwise direction
onto the catalyst. Secure the tip using the 7 mm
wrench provided.
To remove the soldering tip, use the 7 mm wrench
to unscrew the tip in counter-clockwise direction.
Loosen the screw to fit the front tip (screwdriver
not included).
8
MAINTENANCE AND CLEANING
ALWAYS SWITCH OFF THE TOOL AND
!
ALLOW IT TO FULLY COOL DOWN BEFORE
SERVICE AND WARRANTY
8